fishing wire from second floor to garage in first floor
I was trying to drill a 1” hole on the horizontal beam in the wall to fish cable from second floor to garage in first floor. After drilling about 12 inch deep, I cannot go further anymore. Here is few pics about the hole and the wall structure, as well as the drill bit. Please let me know what is going on or if you have any better ideas. Thanks
]1[
]2[
]3
wiring walls
asked 4 hours ago
JasperJasper
285
add a comment |
I was trying to drill a 1” hole on the horizontal beam in the wall to fish cable from second floor to garage in first floor. After drilling about 12 inch deep, I cannot go further anymore. Here is few pics about the hole and the wall structure, as well as the drill bit. Please let me know what is going on or if you have any better ideas. Thanks]1[]2[]3
wiring walls
asked 4 hours ago
JasperJasper
285
add a comment |
I was trying to drill a 1” hole on the horizontal beam in the wall to fish cable from second floor to garage in first floor. After drilling about 12 inch deep, I cannot go further anymore. Here is few pics about the hole and the wall structure, as well as the drill bit. Please let me know what is going on or if you have any better ideas. Thanks]1[]2[]3
wiring walls
asked 4 hours ago
JasperJasper
285
I was trying to drill a 1” hole on the horizontal beam in the wall to fish cable from second floor to garage in first floor. After drilling about 12 inch deep, I cannot go further anymore. Here is few pics about the hole and the wall structure, as well as the drill bit. Please let me know what is going on or if you have any better ideas. Thanks]1[]2[]3
wiring walls
wiring walls
asked 4 hours ago
JasperJasper
285
asked 4 hours ago
JasperJasper
285
asked 4 hours ago
JasperJasper
285
asked 4 hours ago
JasperJasper
285
asked 4 hours ago
JasperJasper
285
285
add a comment |
add a comment |
2 Answers
2
active
oldest
votes
I think that using a spade type of bit there will be really tough going. I would use a regular twist bit. Possibly two if it is really tough going - e.g., 1/2" first and then followup with a 1" through the 1/2" starter hole.
If you have access to do so, it may be easier to drill from the bottom up than from the top down because the hole will empty itself thanks to gravity.
answered 3 hours ago
manassehkatzmanassehkatz
7,5511030
add a comment |
You can purchase really long standard twist bits and they also sell flexible ones that allow you to have the drill outside of the cavity. You then bend it into a hole in the floor plate.
I'd drill a smaller one using one of these bits, and assuming that goes well, look to make it larger, perhaps from the bottom.
Obviously make sure there's nothing below you that wouldn't like being drilled into.
answered 28 mins ago
NormanNorman
101
New contributor
Norman is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
add a comment |
Your Answer
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "73"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
noCode: true, onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fdiy.stackexchange.com%2fquestions%2f155955%2ffishing-wire-from-second-floor-to-garage-in-first-floor%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
2 Answers
2
active
oldest
votes
2 Answers
2
active
oldest
votes
active
oldest
votes
active
oldest
votes
I think that using a spade type of bit there will be really tough going. I would use a regular twist bit. Possibly two if it is really tough going - e.g., 1/2" first and then followup with a 1" through the 1/2" starter hole.
If you have access to do so, it may be easier to drill from the bottom up than from the top down because the hole will empty itself thanks to gravity.
answered 3 hours ago
manassehkatzmanassehkatz
7,5511030
add a comment |
I think that using a spade type of bit there will be really tough going. I would use a regular twist bit. Possibly two if it is really tough going - e.g., 1/2" first and then followup with a 1" through the 1/2" starter hole.
If you have access to do so, it may be easier to drill from the bottom up than from the top down because the hole will empty itself thanks to gravity.
answered 3 hours ago
manassehkatzmanassehkatz
7,5511030
add a comment |
I think that using a spade type of bit there will be really tough going. I would use a regular twist bit. Possibly two if it is really tough going - e.g., 1/2" first and then followup with a 1" through the 1/2" starter hole.
If you have access to do so, it may be easier to drill from the bottom up than from the top down because the hole will empty itself thanks to gravity.
answered 3 hours ago
manassehkatzmanassehkatz
7,5511030
I think that using a spade type of bit there will be really tough going. I would use a regular twist bit. Possibly two if it is really tough going - e.g., 1/2" first and then followup with a 1" through the 1/2" starter hole.
If you have access to do so, it may be easier to drill from the bottom up than from the top down because the hole will empty itself thanks to gravity.
answered 3 hours ago
manassehkatzmanassehkatz
7,5511030
answered 3 hours ago
manassehkatzmanassehkatz
7,5511030
answered 3 hours ago
manassehkatzmanassehkatz
7,5511030
answered 3 hours ago
manassehkatzmanassehkatz
7,5511030
7,5511030
add a comment |
add a comment |
You can purchase really long standard twist bits and they also sell flexible ones that allow you to have the drill outside of the cavity. You then bend it into a hole in the floor plate.
I'd drill a smaller one using one of these bits, and assuming that goes well, look to make it larger, perhaps from the bottom.
Obviously make sure there's nothing below you that wouldn't like being drilled into.
answered 28 mins ago
NormanNorman
101
New contributor
Norman is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
add a comment |
You can purchase really long standard twist bits and they also sell flexible ones that allow you to have the drill outside of the cavity. You then bend it into a hole in the floor plate.
I'd drill a smaller one using one of these bits, and assuming that goes well, look to make it larger, perhaps from the bottom.
Obviously make sure there's nothing below you that wouldn't like being drilled into.
answered 28 mins ago
NormanNorman
101
New contributor
Norman is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
add a comment |
You can purchase really long standard twist bits and they also sell flexible ones that allow you to have the drill outside of the cavity. You then bend it into a hole in the floor plate.
I'd drill a smaller one using one of these bits, and assuming that goes well, look to make it larger, perhaps from the bottom.
Obviously make sure there's nothing below you that wouldn't like being drilled into.
answered 28 mins ago
NormanNorman
101
New contributor
Norman is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
You can purchase really long standard twist bits and they also sell flexible ones that allow you to have the drill outside of the cavity. You then bend it into a hole in the floor plate.
I'd drill a smaller one using one of these bits, and assuming that goes well, look to make it larger, perhaps from the bottom.
Obviously make sure there's nothing below you that wouldn't like being drilled into.
answered 28 mins ago
NormanNorman
101
New contributor
Norman is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
answered 28 mins ago
NormanNorman
101
New contributor
Norman is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
answered 28 mins ago
NormanNorman
101
answered 28 mins ago
NormanNorman
101
101
New contributor
Norman is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
New contributor
Norman is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
Norman is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
add a comment |
add a comment |
Thanks for contributing an answer to Home Improvement Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fdiy.stackexchange.com%2fquestions%2f155955%2ffishing-wire-from-second-floor-to-garage-in-first-floor%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
