Low speed for Atheros AR8151
up vote
0
down vote
favorite
I hope someone can help! i've just cat6 cable through my house and hardwired my HTPC, I decided to do a quick speed test and was only getting ~91 Mb/s both devices have GB ports so i was expecting something higher. The HTPC runs Ubuntu 16.04.5 LTS (GNU/Linux 4.4.0-116-generic x86_64).
i did a:
lspci
and got:
02:00.0 Ethernet controller: Qualcomm Atheros AR8151 v2.0 Gigabit Ethernet (rev c0)
and with
sudo ethtool enp2s0 | grep Speed
and got back: Speed: 100Mb/s
i found this: https://ubuntuforums.org/showthread.php?t=1677122, but when i follow the instructions i get:
Makefile:173: *** *** Aborting the build. *** This driver is not supported on kernel versions older than 2.4.0. Stop.
which i guess is fair enough as the post is pretty old, what are my options get a faster speed? am i doing something wrong?
networking atheros
asked Dec 6 at 14:40
Ashley Guest
31
New contributor
Ashley Guest is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
|
show 1 more comment
up vote
0
down vote
favorite
I hope someone can help! i've just cat6 cable through my house and hardwired my HTPC, I decided to do a quick speed test and was only getting ~91 Mb/s both devices have GB ports so i was expecting something higher. The HTPC runs Ubuntu 16.04.5 LTS (GNU/Linux 4.4.0-116-generic x86_64).
i did a:
lspci
and got:
02:00.0 Ethernet controller: Qualcomm Atheros AR8151 v2.0 Gigabit Ethernet (rev c0)
and with
sudo ethtool enp2s0 | grep Speed
and got back: Speed: 100Mb/s
i found this: https://ubuntuforums.org/showthread.php?t=1677122, but when i follow the instructions i get:
Makefile:173: *** *** Aborting the build. *** This driver is not supported on kernel versions older than 2.4.0. Stop.
which i guess is fair enough as the post is pretty old, what are my options get a faster speed? am i doing something wrong?
networking atheros
asked Dec 6 at 14:40
Ashley Guest
31
New contributor
Ashley Guest is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
Are you quite certain that you are using a known gigabit-capable cable, i.e. cat5e or cat6? Welcome to Ask Ubuntu.
– chili555
Dec 6 at 15:20
Hmmm nope! good call, the patch cables i'm using are probably quite old thinking about it. i shall check, if I am using a old cat5 cable would that be the reason why its only returning 100Mb/s when i run sudo ethtool enp2s0 | grep Speed ???
– Ashley Guest
Dec 6 at 16:03
Absolutely! Been there and done that myself. ethtool will report the maximum that the ethernet card is able to negotiate with the router/switch. A small pipe means low speeds.
– chili555
Dec 6 at 16:11
PS- If you have tp buy a better cable, I suggest that you get the very fastest available; that is the most future-proof. I prefer cat7 to cat6a if available and cat 6a over cat6 and so on. Please keep us posted.
– chili555
Dec 6 at 16:25
Just swapped over the cable, the original cable didn't have any writing on it but it must be cat5 as I swapped it with another that says cat5e and now reporting 1000Mb/s. Lan speed test is showing 891Mb/s.... much better! school boy error, i should have checked! will look into getting a better cable in the future as eventually i will have 3 additional devices feeding off the HTPC. Thanks for your help!
– Ashley Guest
Dec 6 at 17:35
|
show 1 more comment
up vote
0
down vote
favorite
up vote
0
down vote
favorite
I hope someone can help! i've just cat6 cable through my house and hardwired my HTPC, I decided to do a quick speed test and was only getting ~91 Mb/s both devices have GB ports so i was expecting something higher. The HTPC runs Ubuntu 16.04.5 LTS (GNU/Linux 4.4.0-116-generic x86_64).
i did a:
lspci
and got:
02:00.0 Ethernet controller: Qualcomm Atheros AR8151 v2.0 Gigabit Ethernet (rev c0)
and with
sudo ethtool enp2s0 | grep Speed
and got back: Speed: 100Mb/s
i found this: https://ubuntuforums.org/showthread.php?t=1677122, but when i follow the instructions i get:
Makefile:173: *** *** Aborting the build. *** This driver is not supported on kernel versions older than 2.4.0. Stop.
which i guess is fair enough as the post is pretty old, what are my options get a faster speed? am i doing something wrong?
networking atheros
asked Dec 6 at 14:40
Ashley Guest
31
New contributor
Ashley Guest is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
I hope someone can help! i've just cat6 cable through my house and hardwired my HTPC, I decided to do a quick speed test and was only getting ~91 Mb/s both devices have GB ports so i was expecting something higher. The HTPC runs Ubuntu 16.04.5 LTS (GNU/Linux 4.4.0-116-generic x86_64).
i did a:
lspci
and got:
02:00.0 Ethernet controller: Qualcomm Atheros AR8151 v2.0 Gigabit Ethernet (rev c0)
and with
sudo ethtool enp2s0 | grep Speed
and got back: Speed: 100Mb/s
i found this: https://ubuntuforums.org/showthread.php?t=1677122, but when i follow the instructions i get:
Makefile:173: *** *** Aborting the build. *** This driver is not supported on kernel versions older than 2.4.0. Stop.
which i guess is fair enough as the post is pretty old, what are my options get a faster speed? am i doing something wrong?
networking atheros
networking atheros
asked Dec 6 at 14:40
Ashley Guest
31
New contributor
Ashley Guest is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked Dec 6 at 14:40
Ashley Guest
31
New contributor
Ashley Guest is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked Dec 6 at 14:40
Ashley Guest
31
New contributor
Ashley Guest is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked Dec 6 at 14:40
Ashley Guest
31
asked Dec 6 at 14:40
Ashley Guest
31
31
New contributor
Ashley Guest is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
New contributor
Ashley Guest is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
Ashley Guest is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
Are you quite certain that you are using a known gigabit-capable cable, i.e. cat5e or cat6? Welcome to Ask Ubuntu.
– chili555
Dec 6 at 15:20
Hmmm nope! good call, the patch cables i'm using are probably quite old thinking about it. i shall check, if I am using a old cat5 cable would that be the reason why its only returning 100Mb/s when i run sudo ethtool enp2s0 | grep Speed ???
– Ashley Guest
Dec 6 at 16:03
Absolutely! Been there and done that myself. ethtool will report the maximum that the ethernet card is able to negotiate with the router/switch. A small pipe means low speeds.
– chili555
Dec 6 at 16:11
PS- If you have tp buy a better cable, I suggest that you get the very fastest available; that is the most future-proof. I prefer cat7 to cat6a if available and cat 6a over cat6 and so on. Please keep us posted.
– chili555
Dec 6 at 16:25
Just swapped over the cable, the original cable didn't have any writing on it but it must be cat5 as I swapped it with another that says cat5e and now reporting 1000Mb/s. Lan speed test is showing 891Mb/s.... much better! school boy error, i should have checked! will look into getting a better cable in the future as eventually i will have 3 additional devices feeding off the HTPC. Thanks for your help!
– Ashley Guest
Dec 6 at 17:35
|
show 1 more comment
Are you quite certain that you are using a known gigabit-capable cable, i.e. cat5e or cat6? Welcome to Ask Ubuntu.
– chili555
Dec 6 at 15:20
Hmmm nope! good call, the patch cables i'm using are probably quite old thinking about it. i shall check, if I am using a old cat5 cable would that be the reason why its only returning 100Mb/s when i run sudo ethtool enp2s0 | grep Speed ???
– Ashley Guest
Dec 6 at 16:03
Absolutely! Been there and done that myself. ethtool will report the maximum that the ethernet card is able to negotiate with the router/switch. A small pipe means low speeds.
– chili555
Dec 6 at 16:11
PS- If you have tp buy a better cable, I suggest that you get the very fastest available; that is the most future-proof. I prefer cat7 to cat6a if available and cat 6a over cat6 and so on. Please keep us posted.
– chili555
Dec 6 at 16:25
Just swapped over the cable, the original cable didn't have any writing on it but it must be cat5 as I swapped it with another that says cat5e and now reporting 1000Mb/s. Lan speed test is showing 891Mb/s.... much better! school boy error, i should have checked! will look into getting a better cable in the future as eventually i will have 3 additional devices feeding off the HTPC. Thanks for your help!
– Ashley Guest
Dec 6 at 17:35
Are you quite certain that you are using a known gigabit-capable cable, i.e. cat5e or cat6? Welcome to Ask Ubuntu.
– chili555
Dec 6 at 15:20
Are you quite certain that you are using a known gigabit-capable cable, i.e. cat5e or cat6? Welcome to Ask Ubuntu.
– chili555
Dec 6 at 15:20
Hmmm nope! good call, the patch cables i'm using are probably quite old thinking about it. i shall check, if I am using a old cat5 cable would that be the reason why its only returning 100Mb/s when i run sudo ethtool enp2s0 | grep Speed ???
– Ashley Guest
Dec 6 at 16:03
Hmmm nope! good call, the patch cables i'm using are probably quite old thinking about it. i shall check, if I am using a old cat5 cable would that be the reason why its only returning 100Mb/s when i run sudo ethtool enp2s0 | grep Speed ???
– Ashley Guest
Dec 6 at 16:03
Absolutely! Been there and done that myself. ethtool will report the maximum that the ethernet card is able to negotiate with the router/switch. A small pipe means low speeds.
– chili555
Dec 6 at 16:11
Absolutely! Been there and done that myself. ethtool will report the maximum that the ethernet card is able to negotiate with the router/switch. A small pipe means low speeds.
– chili555
Dec 6 at 16:11
PS- If you have tp buy a better cable, I suggest that you get the very fastest available; that is the most future-proof. I prefer cat7 to cat6a if available and cat 6a over cat6 and so on. Please keep us posted.
– chili555
Dec 6 at 16:25
PS- If you have tp buy a better cable, I suggest that you get the very fastest available; that is the most future-proof. I prefer cat7 to cat6a if available and cat 6a over cat6 and so on. Please keep us posted.
– chili555
Dec 6 at 16:25
Just swapped over the cable, the original cable didn't have any writing on it but it must be cat5 as I swapped it with another that says cat5e and now reporting 1000Mb/s. Lan speed test is showing 891Mb/s.... much better! school boy error, i should have checked! will look into getting a better cable in the future as eventually i will have 3 additional devices feeding off the HTPC. Thanks for your help!
– Ashley Guest
Dec 6 at 17:35
Just swapped over the cable, the original cable didn't have any writing on it but it must be cat5 as I swapped it with another that says cat5e and now reporting 1000Mb/s. Lan speed test is showing 891Mb/s.... much better! school boy error, i should have checked! will look into getting a better cable in the future as eventually i will have 3 additional devices feeding off the HTPC. Thanks for your help!
– Ashley Guest
Dec 6 at 17:35
|
show 1 more comment
1 Answer
1
active
oldest
votes
up vote
1
down vote
accepted
Please be quite certain that you are using a known gigabit-capable cable, i.e. cat 5e or cat 6 or better. If your computer has been connected for some time, it is entirely possible that it was connected with cat 5 which only supports 100 Mb/s: https://en.wikipedia.org/wiki/Category_5_cable
Category 5 cable, commonly referred to as Cat 5, is a twisted pair
cable for computer networks. The cable standard provides performance
of up to 100 Mbps
If you have to buy a better cable, I suggest that you get the very fastest available; that is the most future-proof. I prefer cat7 to cat6a if available and cat 6a over cat6 and so on.
You might also temporarily swap in a known cat 5e or better cable to test the result.
answered Dec 6 at 20:10
chili555
37.9k55077
add a comment |
1 Answer
1
active
oldest
votes
1 Answer
1
active
oldest
votes
active
oldest
votes
active
oldest
votes
up vote
1
down vote
accepted
Please be quite certain that you are using a known gigabit-capable cable, i.e. cat 5e or cat 6 or better. If your computer has been connected for some time, it is entirely possible that it was connected with cat 5 which only supports 100 Mb/s: https://en.wikipedia.org/wiki/Category_5_cable
Category 5 cable, commonly referred to as Cat 5, is a twisted pair
cable for computer networks. The cable standard provides performance
of up to 100 Mbps
If you have to buy a better cable, I suggest that you get the very fastest available; that is the most future-proof. I prefer cat7 to cat6a if available and cat 6a over cat6 and so on.
You might also temporarily swap in a known cat 5e or better cable to test the result.
answered Dec 6 at 20:10
chili555
37.9k55077
add a comment |
up vote
1
down vote
accepted
Please be quite certain that you are using a known gigabit-capable cable, i.e. cat 5e or cat 6 or better. If your computer has been connected for some time, it is entirely possible that it was connected with cat 5 which only supports 100 Mb/s: https://en.wikipedia.org/wiki/Category_5_cable
Category 5 cable, commonly referred to as Cat 5, is a twisted pair
cable for computer networks. The cable standard provides performance
of up to 100 Mbps
If you have to buy a better cable, I suggest that you get the very fastest available; that is the most future-proof. I prefer cat7 to cat6a if available and cat 6a over cat6 and so on.
You might also temporarily swap in a known cat 5e or better cable to test the result.
answered Dec 6 at 20:10
chili555
37.9k55077
add a comment |
up vote
1
down vote
accepted
up vote
1
down vote
accepted
Please be quite certain that you are using a known gigabit-capable cable, i.e. cat 5e or cat 6 or better. If your computer has been connected for some time, it is entirely possible that it was connected with cat 5 which only supports 100 Mb/s: https://en.wikipedia.org/wiki/Category_5_cable
Category 5 cable, commonly referred to as Cat 5, is a twisted pair
cable for computer networks. The cable standard provides performance
of up to 100 Mbps
If you have to buy a better cable, I suggest that you get the very fastest available; that is the most future-proof. I prefer cat7 to cat6a if available and cat 6a over cat6 and so on.
You might also temporarily swap in a known cat 5e or better cable to test the result.
answered Dec 6 at 20:10
chili555
37.9k55077
Please be quite certain that you are using a known gigabit-capable cable, i.e. cat 5e or cat 6 or better. If your computer has been connected for some time, it is entirely possible that it was connected with cat 5 which only supports 100 Mb/s: https://en.wikipedia.org/wiki/Category_5_cable
Category 5 cable, commonly referred to as Cat 5, is a twisted pair
cable for computer networks. The cable standard provides performance
of up to 100 Mbps
If you have to buy a better cable, I suggest that you get the very fastest available; that is the most future-proof. I prefer cat7 to cat6a if available and cat 6a over cat6 and so on.
You might also temporarily swap in a known cat 5e or better cable to test the result.
answered Dec 6 at 20:10
chili555
37.9k55077
answered Dec 6 at 20:10
chili555
37.9k55077
answered Dec 6 at 20:10
chili555
37.9k55077
answered Dec 6 at 20:10
chili555
37.9k55077
37.9k55077
add a comment |
add a comment |
Ashley Guest is a new contributor. Be nice, and check out our Code of Conduct.
Ashley Guest is a new contributor. Be nice, and check out our Code of Conduct.
Ashley Guest is a new contributor. Be nice, and check out our Code of Conduct.
Ashley Guest is a new contributor. Be nice, and check out our Code of Conduct.
Thanks for contributing an answer to Ask Ubuntu!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Some of your past answers have not been well-received, and you're in danger of being blocked from answering.
Please pay close attention to the following guidance:
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2faskubuntu.com%2fquestions%2f1098944%2flow-speed-for-atheros-ar8151%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Are you quite certain that you are using a known gigabit-capable cable, i.e. cat5e or cat6? Welcome to Ask Ubuntu.
– chili555
Dec 6 at 15:20
Hmmm nope! good call, the patch cables i'm using are probably quite old thinking about it. i shall check, if I am using a old cat5 cable would that be the reason why its only returning 100Mb/s when i run sudo ethtool enp2s0 | grep Speed ???
– Ashley Guest
Dec 6 at 16:03
Absolutely! Been there and done that myself. ethtool will report the maximum that the ethernet card is able to negotiate with the router/switch. A small pipe means low speeds.
– chili555
Dec 6 at 16:11
PS- If you have tp buy a better cable, I suggest that you get the very fastest available; that is the most future-proof. I prefer cat7 to cat6a if available and cat 6a over cat6 and so on. Please keep us posted.
– chili555
Dec 6 at 16:25
Just swapped over the cable, the original cable didn't have any writing on it but it must be cat5 as I swapped it with another that says cat5e and now reporting 1000Mb/s. Lan speed test is showing 891Mb/s.... much better! school boy error, i should have checked! will look into getting a better cable in the future as eventually i will have 3 additional devices feeding off the HTPC. Thanks for your help!
– Ashley Guest
Dec 6 at 17:35