Can I connect a DC high voltage booster directly to my Raspberry Pi?





.everyoneloves__top-leaderboard:empty,.everyoneloves__mid-leaderboard:empty,.everyoneloves__bot-mid-leaderboard:empty{ margin-bottom:0;
}







1












$begingroup$


I have one of these modules:




HV transformer




Is it safe to connect it to two pins to my Raspberry Pi, directly, and turn it on by emitting HIGH on one of the pins (the other one being the ground), which is around 5V, if I am not wrong?



Will that use too much power from the Raspberry Pi or maybe burn it?










share|improve this question











$endgroup$








  • 2




    $begingroup$
    Without engineering data (no a link to a sales page dies not qualify) this is off topic here. But it sounds like a terrible technical idea, probably in pursuit of a misguided or improper goal.
    $endgroup$
    – Chris Stratton
    2 days ago






  • 1




    $begingroup$
    There's nothing to be gained in casting aspersions on the OP's motives. Whatever these modules are, they're apparently cheap and plentiful on ebay, so plenty of people will likely be playing with them for all sorts of reasons. Best if they know how to do that without killing their Raspberry Pi's. :)
    $endgroup$
    – aroth
    2 days ago


















1












$begingroup$


I have one of these modules:




HV transformer




Is it safe to connect it to two pins to my Raspberry Pi, directly, and turn it on by emitting HIGH on one of the pins (the other one being the ground), which is around 5V, if I am not wrong?



Will that use too much power from the Raspberry Pi or maybe burn it?










share|improve this question











$endgroup$








  • 2




    $begingroup$
    Without engineering data (no a link to a sales page dies not qualify) this is off topic here. But it sounds like a terrible technical idea, probably in pursuit of a misguided or improper goal.
    $endgroup$
    – Chris Stratton
    2 days ago






  • 1




    $begingroup$
    There's nothing to be gained in casting aspersions on the OP's motives. Whatever these modules are, they're apparently cheap and plentiful on ebay, so plenty of people will likely be playing with them for all sorts of reasons. Best if they know how to do that without killing their Raspberry Pi's. :)
    $endgroup$
    – aroth
    2 days ago














1












1








1





$begingroup$


I have one of these modules:




HV transformer




Is it safe to connect it to two pins to my Raspberry Pi, directly, and turn it on by emitting HIGH on one of the pins (the other one being the ground), which is around 5V, if I am not wrong?



Will that use too much power from the Raspberry Pi or maybe burn it?










share|improve this question











$endgroup$




I have one of these modules:




HV transformer




Is it safe to connect it to two pins to my Raspberry Pi, directly, and turn it on by emitting HIGH on one of the pins (the other one being the ground), which is around 5V, if I am not wrong?



Will that use too much power from the Raspberry Pi or maybe burn it?







dc raspberry-pi high-voltage






share|improve this question















share|improve this question













share|improve this question




share|improve this question








edited 2 days ago









feetwet

1,15141839




1,15141839










asked Apr 10 at 4:56









Ionică BizăuIonică Bizău

17718




17718








  • 2




    $begingroup$
    Without engineering data (no a link to a sales page dies not qualify) this is off topic here. But it sounds like a terrible technical idea, probably in pursuit of a misguided or improper goal.
    $endgroup$
    – Chris Stratton
    2 days ago






  • 1




    $begingroup$
    There's nothing to be gained in casting aspersions on the OP's motives. Whatever these modules are, they're apparently cheap and plentiful on ebay, so plenty of people will likely be playing with them for all sorts of reasons. Best if they know how to do that without killing their Raspberry Pi's. :)
    $endgroup$
    – aroth
    2 days ago














  • 2




    $begingroup$
    Without engineering data (no a link to a sales page dies not qualify) this is off topic here. But it sounds like a terrible technical idea, probably in pursuit of a misguided or improper goal.
    $endgroup$
    – Chris Stratton
    2 days ago






  • 1




    $begingroup$
    There's nothing to be gained in casting aspersions on the OP's motives. Whatever these modules are, they're apparently cheap and plentiful on ebay, so plenty of people will likely be playing with them for all sorts of reasons. Best if they know how to do that without killing their Raspberry Pi's. :)
    $endgroup$
    – aroth
    2 days ago








2




2




$begingroup$
Without engineering data (no a link to a sales page dies not qualify) this is off topic here. But it sounds like a terrible technical idea, probably in pursuit of a misguided or improper goal.
$endgroup$
– Chris Stratton
2 days ago




$begingroup$
Without engineering data (no a link to a sales page dies not qualify) this is off topic here. But it sounds like a terrible technical idea, probably in pursuit of a misguided or improper goal.
$endgroup$
– Chris Stratton
2 days ago




1




1




$begingroup$
There's nothing to be gained in casting aspersions on the OP's motives. Whatever these modules are, they're apparently cheap and plentiful on ebay, so plenty of people will likely be playing with them for all sorts of reasons. Best if they know how to do that without killing their Raspberry Pi's. :)
$endgroup$
– aroth
2 days ago




$begingroup$
There's nothing to be gained in casting aspersions on the OP's motives. Whatever these modules are, they're apparently cheap and plentiful on ebay, so plenty of people will likely be playing with them for all sorts of reasons. Best if they know how to do that without killing their Raspberry Pi's. :)
$endgroup$
– aroth
2 days ago










3 Answers
3






active

oldest

votes


















8












$begingroup$

The advert says it needs 5 Amperes. That’s hundreds of times more than a Raspberry Pi GPIO can supply.



You would need a driver, preferably with isolation, and a separate power supply capable of at least 5A. One solution would be a CPC709J, with a suitable series resistor for the LED.



You may well cause disruption or damage even with that, but the chances are better. You’re essentially putting a multi-watt spark-gap transmitter in close proximity to an unshielded microcomputer.






share|improve this answer











$endgroup$













  • $begingroup$
    Thanks! I think using a relay would be a solution too, right?
    $endgroup$
    – Ionică Bizău
    2 days ago










  • $begingroup$
    Absolutely, but you also then need to build a relay driver, and relays don’t give perfect isolation either.
    $endgroup$
    – Spehro Pefhany
    2 days ago



















5












$begingroup$

Apart from not having enough energy to drive that circuit:



Generating sparks near a piece of electronics is never a good idea.



Although the circuit has protection on some of the I/O ports, especially the HDMI and USB interfaces, there is non on the GPIO pins. Those have the standard ESD protection which is designed for, well... ESD. It is NOT designed to handle the energy which comes from huge voltage sparks.






share|improve this answer









$endgroup$





















    5












    $begingroup$

    The micro-lightning arc HV noise generator needs 1 or Li-Ion cells to power it. If should never be operated near any computer.



    If it operates near an R-Pi, it will cause functional failure and possible damage to signal ports on cables acting as an antenna.






    share|improve this answer









    $endgroup$














      Your Answer






      StackExchange.ifUsing("editor", function () {
      return StackExchange.using("schematics", function () {
      StackExchange.schematics.init();
      });
      }, "cicuitlab");

      StackExchange.ready(function() {
      var channelOptions = {
      tags: "".split(" "),
      id: "135"
      };
      initTagRenderer("".split(" "), "".split(" "), channelOptions);

      StackExchange.using("externalEditor", function() {
      // Have to fire editor after snippets, if snippets enabled
      if (StackExchange.settings.snippets.snippetsEnabled) {
      StackExchange.using("snippets", function() {
      createEditor();
      });
      }
      else {
      createEditor();
      }
      });

      function createEditor() {
      StackExchange.prepareEditor({
      heartbeatType: 'answer',
      autoActivateHeartbeat: false,
      convertImagesToLinks: false,
      noModals: true,
      showLowRepImageUploadWarning: true,
      reputationToPostImages: null,
      bindNavPrevention: true,
      postfix: "",
      imageUploader: {
      brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
      contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
      allowUrls: true
      },
      onDemand: true,
      discardSelector: ".discard-answer"
      ,immediatelyShowMarkdownHelp:true
      });


      }
      });














      draft saved

      draft discarded


















      StackExchange.ready(
      function () {
      StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f431740%2fcan-i-connect-a-dc-high-voltage-booster-directly-to-my-raspberry-pi%23new-answer', 'question_page');
      }
      );

      Post as a guest















      Required, but never shown

























      3 Answers
      3






      active

      oldest

      votes








      3 Answers
      3






      active

      oldest

      votes









      active

      oldest

      votes






      active

      oldest

      votes









      8












      $begingroup$

      The advert says it needs 5 Amperes. That’s hundreds of times more than a Raspberry Pi GPIO can supply.



      You would need a driver, preferably with isolation, and a separate power supply capable of at least 5A. One solution would be a CPC709J, with a suitable series resistor for the LED.



      You may well cause disruption or damage even with that, but the chances are better. You’re essentially putting a multi-watt spark-gap transmitter in close proximity to an unshielded microcomputer.






      share|improve this answer











      $endgroup$













      • $begingroup$
        Thanks! I think using a relay would be a solution too, right?
        $endgroup$
        – Ionică Bizău
        2 days ago










      • $begingroup$
        Absolutely, but you also then need to build a relay driver, and relays don’t give perfect isolation either.
        $endgroup$
        – Spehro Pefhany
        2 days ago
















      8












      $begingroup$

      The advert says it needs 5 Amperes. That’s hundreds of times more than a Raspberry Pi GPIO can supply.



      You would need a driver, preferably with isolation, and a separate power supply capable of at least 5A. One solution would be a CPC709J, with a suitable series resistor for the LED.



      You may well cause disruption or damage even with that, but the chances are better. You’re essentially putting a multi-watt spark-gap transmitter in close proximity to an unshielded microcomputer.






      share|improve this answer











      $endgroup$













      • $begingroup$
        Thanks! I think using a relay would be a solution too, right?
        $endgroup$
        – Ionică Bizău
        2 days ago










      • $begingroup$
        Absolutely, but you also then need to build a relay driver, and relays don’t give perfect isolation either.
        $endgroup$
        – Spehro Pefhany
        2 days ago














      8












      8








      8





      $begingroup$

      The advert says it needs 5 Amperes. That’s hundreds of times more than a Raspberry Pi GPIO can supply.



      You would need a driver, preferably with isolation, and a separate power supply capable of at least 5A. One solution would be a CPC709J, with a suitable series resistor for the LED.



      You may well cause disruption or damage even with that, but the chances are better. You’re essentially putting a multi-watt spark-gap transmitter in close proximity to an unshielded microcomputer.






      share|improve this answer











      $endgroup$



      The advert says it needs 5 Amperes. That’s hundreds of times more than a Raspberry Pi GPIO can supply.



      You would need a driver, preferably with isolation, and a separate power supply capable of at least 5A. One solution would be a CPC709J, with a suitable series resistor for the LED.



      You may well cause disruption or damage even with that, but the chances are better. You’re essentially putting a multi-watt spark-gap transmitter in close proximity to an unshielded microcomputer.







      share|improve this answer














      share|improve this answer



      share|improve this answer








      edited 2 days ago

























      answered 2 days ago









      Spehro PefhanySpehro Pefhany

      213k5162432




      213k5162432












      • $begingroup$
        Thanks! I think using a relay would be a solution too, right?
        $endgroup$
        – Ionică Bizău
        2 days ago










      • $begingroup$
        Absolutely, but you also then need to build a relay driver, and relays don’t give perfect isolation either.
        $endgroup$
        – Spehro Pefhany
        2 days ago


















      • $begingroup$
        Thanks! I think using a relay would be a solution too, right?
        $endgroup$
        – Ionică Bizău
        2 days ago










      • $begingroup$
        Absolutely, but you also then need to build a relay driver, and relays don’t give perfect isolation either.
        $endgroup$
        – Spehro Pefhany
        2 days ago
















      $begingroup$
      Thanks! I think using a relay would be a solution too, right?
      $endgroup$
      – Ionică Bizău
      2 days ago




      $begingroup$
      Thanks! I think using a relay would be a solution too, right?
      $endgroup$
      – Ionică Bizău
      2 days ago












      $begingroup$
      Absolutely, but you also then need to build a relay driver, and relays don’t give perfect isolation either.
      $endgroup$
      – Spehro Pefhany
      2 days ago




      $begingroup$
      Absolutely, but you also then need to build a relay driver, and relays don’t give perfect isolation either.
      $endgroup$
      – Spehro Pefhany
      2 days ago













      5












      $begingroup$

      Apart from not having enough energy to drive that circuit:



      Generating sparks near a piece of electronics is never a good idea.



      Although the circuit has protection on some of the I/O ports, especially the HDMI and USB interfaces, there is non on the GPIO pins. Those have the standard ESD protection which is designed for, well... ESD. It is NOT designed to handle the energy which comes from huge voltage sparks.






      share|improve this answer









      $endgroup$


















        5












        $begingroup$

        Apart from not having enough energy to drive that circuit:



        Generating sparks near a piece of electronics is never a good idea.



        Although the circuit has protection on some of the I/O ports, especially the HDMI and USB interfaces, there is non on the GPIO pins. Those have the standard ESD protection which is designed for, well... ESD. It is NOT designed to handle the energy which comes from huge voltage sparks.






        share|improve this answer









        $endgroup$
















          5












          5








          5





          $begingroup$

          Apart from not having enough energy to drive that circuit:



          Generating sparks near a piece of electronics is never a good idea.



          Although the circuit has protection on some of the I/O ports, especially the HDMI and USB interfaces, there is non on the GPIO pins. Those have the standard ESD protection which is designed for, well... ESD. It is NOT designed to handle the energy which comes from huge voltage sparks.






          share|improve this answer









          $endgroup$



          Apart from not having enough energy to drive that circuit:



          Generating sparks near a piece of electronics is never a good idea.



          Although the circuit has protection on some of the I/O ports, especially the HDMI and USB interfaces, there is non on the GPIO pins. Those have the standard ESD protection which is designed for, well... ESD. It is NOT designed to handle the energy which comes from huge voltage sparks.







          share|improve this answer












          share|improve this answer



          share|improve this answer










          answered Apr 10 at 5:06









          OldfartOldfart

          8,8462927




          8,8462927























              5












              $begingroup$

              The micro-lightning arc HV noise generator needs 1 or Li-Ion cells to power it. If should never be operated near any computer.



              If it operates near an R-Pi, it will cause functional failure and possible damage to signal ports on cables acting as an antenna.






              share|improve this answer









              $endgroup$


















                5












                $begingroup$

                The micro-lightning arc HV noise generator needs 1 or Li-Ion cells to power it. If should never be operated near any computer.



                If it operates near an R-Pi, it will cause functional failure and possible damage to signal ports on cables acting as an antenna.






                share|improve this answer









                $endgroup$
















                  5












                  5








                  5





                  $begingroup$

                  The micro-lightning arc HV noise generator needs 1 or Li-Ion cells to power it. If should never be operated near any computer.



                  If it operates near an R-Pi, it will cause functional failure and possible damage to signal ports on cables acting as an antenna.






                  share|improve this answer









                  $endgroup$



                  The micro-lightning arc HV noise generator needs 1 or Li-Ion cells to power it. If should never be operated near any computer.



                  If it operates near an R-Pi, it will cause functional failure and possible damage to signal ports on cables acting as an antenna.







                  share|improve this answer












                  share|improve this answer



                  share|improve this answer










                  answered 2 days ago









                  Sunnyskyguy EE75Sunnyskyguy EE75

                  71.5k227103




                  71.5k227103






























                      draft saved

                      draft discarded




















































                      Thanks for contributing an answer to Electrical Engineering Stack Exchange!


                      • Please be sure to answer the question. Provide details and share your research!

                      But avoid



                      • Asking for help, clarification, or responding to other answers.

                      • Making statements based on opinion; back them up with references or personal experience.


                      Use MathJax to format equations. MathJax reference.


                      To learn more, see our tips on writing great answers.




                      draft saved


                      draft discarded














                      StackExchange.ready(
                      function () {
                      StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f431740%2fcan-i-connect-a-dc-high-voltage-booster-directly-to-my-raspberry-pi%23new-answer', 'question_page');
                      }
                      );

                      Post as a guest















                      Required, but never shown





















































                      Required, but never shown














                      Required, but never shown












                      Required, but never shown







                      Required, but never shown

































                      Required, but never shown














                      Required, but never shown












                      Required, but never shown







                      Required, but never shown







                      Popular posts from this blog

                      數位音樂下載

                      When can things happen in Etherscan, such as the picture below?

                      格利澤436b