Wireless won't connect!
.everyoneloves__top-leaderboard:empty,.everyoneloves__mid-leaderboard:empty,.everyoneloves__bot-mid-leaderboard:empty{ margin-bottom:0;
}
I recently installed Ubuntu onto my Dell Inspiron 1545 laptop.
I can connect to the Internet via Ethernet, but wireless won't work. The prompt to put in the wifi password pops up, but when I put in the password, it simply says connecting and the prompt for the password comes back up! The prompt will come back up every two or three minutes, but the same thing happens.
I've tried to install drivers using Windows Wireless Drivers, but I can't seem to figure it out. My wireless card is an Atheros AR928X. This is my first time using Ubuntu.
Here is the output of the commands I've been asked to run:
1- Output of lspci -nnk | grep -iA2 net
$ lspci -nnk | grep -iA2 net
09:00.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8040 PCI-E Fast Ethernet Controller [11ab:4354] (rev 13)
Subsystem: Dell Device [1028:02aa]
Kernel driver in use: sky2
--
0c:00.0 Network controller [0280]: Atheros Communications Inc. AR928X Wireless Network Adapter (PCI-Express) [168c:002a] (rev 01)
Subsystem: Atheros Communications Inc. Device [168c:0200]
Kernel driver in use: ath9k
2- Output of lsusb
$ lsusb
Bus 001 Device 003: ID 0c45:63ee Microdia
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
3- Output of nm-tool
, sudo iwlist scan
and iwconfig
$ nm-tool
NetworkManager Tool
State: connected (global)
- Device: eth0 [Wired connection 1] -------------------------------------------
Type: Wired
Driver: sky2
State: connected
Default: yes
HW Address: 00:25:64:44:02:7D
Capabilities:
Carrier Detect: yes
Speed: 100 Mb/s
Wired Properties
Carrier: on
IPv4 Settings:
Address: 192.168.1.90
Prefix: 24 (255.255.255.0)
Gateway: 192.168.1.254
DNS: 192.168.1.254
DNS: 75.153.176.9
- Device: wlan0 ----------------------------------------------------------------
Type: 802.11 WiFi
Driver: ath9k
State: disconnected
Default: no
HW Address: 00:22:5F:C2:08:1F
Capabilities:
Wireless Properties
WEP Encryption: yes
WPA Encryption: yes
WPA2 Encryption: yes
Wireless Access Points
beau: Infra, 00:26:B8:ED:E6:CC, Freq 2422 MHz, Rate 54 Mb/s, Strength 95 WPA
verjee: Infra, F0:D1:A9:14:03:7A, Freq 2452 MHz, Rate 54 Mb/s, Strength 32 WPA2
$ sudo iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
wlan0 Scan completed :
Cell 01 - Address: 00:26:B8:ED:E6:CC
Channel:3
Frequency:2.422 GHz (Channel 3)
Quality=64/70 Signal level=-46 dBm
Encryption key:on
ESSID:"beau"
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s
24 Mb/s; 36 Mb/s; 54 Mb/s
Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 48 Mb/s
Mode:Master
Extra:tsf=0000024523a5e000
Extra: Last beacon: 36ms ago
IE: Unknown: 000462656175
IE: Unknown: 010882848B962430486C
IE: Unknown: 030103
IE: Unknown: 2A0100
IE: Unknown: 2F0100
IE: Unknown: 32040C121860
IE: Unknown: 2D1A6C181BFFFF000000000000000000000000000000000000000000
IE: Unknown: 3D1603001300000000000000000000000000000000000000
IE: Unknown: DD090010180202F0050000
IE: WPA Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : TKIP
IE: Unknown: DD180050F2020101800003A4000027A4000042435E0062322F00
IE: Unknown: DD1E00904C336C181BFFFF000000000000000000000000000000000000000000
IE: Unknown: DD1A00904C3403001300000000000000000000000000000000000000
Cell 02 - Address: F0:D1:A9:14:03:7A
Channel:9
Frequency:2.452 GHz (Channel 9)
Quality=27/70 Signal level=-83 dBm
Encryption key:on
ESSID:"verjee"
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
9 Mb/s; 12 Mb/s; 18 Mb/s
Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s
Mode:Master
Extra:tsf=000000173491f180
Extra: Last beacon: 3636ms ago
IE: Unknown: 00067665726A6565
IE: Unknown: 010882848B960C121824
IE: Unknown: 030109
IE: Unknown: 0706434120010B1E
IE: Unknown: 2A0100
IE: Unknown: 32043048606C
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : CCMP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : PSK
IE: Unknown: 2D1AAD511BFFFF000000000000000000000000000000000000000000
IE: Unknown: 33027E9D
IE: Unknown: 3D1609080400000000000000000000000000000000000000
IE: Unknown: 46050200010000
IE: Unknown: DD180050F2020101010003A4000027A4000042435E0062322F00
IE: Unknown: DD0700039301730B20
IE: Unknown: DD0E0017F20700010106F0D1A914037A
$ iwconfig
wlan0 IEEE 802.11abgn ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=16 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Power Management:off
lo no wireless extensions.
eth0 no wireless extensions.
Authentication Suites (1) : PSK
4- Output of rfkill list all
$ rfkill list all
0: phy0: Wireless LAN
Soft blocked: no
Hard blocked: no
5- Output of lsmod
$ lsmod
Module Size Used by
bnep 17791 2
rfcomm 38104 0
bluetooth 189625 10 bnep,rfcomm
parport_pc 32115 0
ppdev 12850 0
snd_hda_codec_idt 60238 1
arc4 12474 2
snd_hda_intel 32983 5
snd_hda_codec 116477 2 snd_hda_codec_idt,snd_hda_intel
snd_hwdep 13277 1 snd_hda_codec
joydev 17394 0
ath9k 122028 0
mac80211 475546 1 ath9k
snd_pcm 81124 3 snd_hda_intel,snd_hda_codec
snd_seq_midi 13133 0
snd_rawmidi 25426 1 snd_seq_midi
snd_seq_midi_event 14476 1 snd_seq_midi
ath9k_common 13782 1 ath9k
ath9k_hw 384090 2 ath9k,ath9k_common
i915 479235 4
uvcvideo 72249 0
snd_seq 51594 2 snd_seq_midi,snd_seq_midi_event
snd_timer 28932 2 snd_pcm,snd_seq
snd_seq_device 14138 3 snd_seq_midi,snd_rawmidi,snd_seq
videobuf2_core 32212 1 uvcvideo
ath 19436 3 ath9k,ath9k_common,ath9k_hw
drm_kms_helper 47459 1 i915
cfg80211 181041 3 ath9k,mac80211,ath
drm 240443 5 i915,drm_kms_helper
psmouse 91381 0
videodev 100265 2 uvcvideo,videobuf2_core
snd 62675 18 snd_hda_codec_idt,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
videobuf2_vmalloc 12757 1 uvcvideo
videobuf2_memops 13213 1 videobuf2_vmalloc
dell_wmi 12602 0
coretemp 13362 0
sparse_keymap 13659 1 dell_wmi
gpio_ich 13160 0
wmi 18745 1 dell_wmi
dell_laptop 17210 0
microcode 18396 0
dcdbas 14099 1 dell_laptop
soundcore 14636 1 snd
snd_page_alloc 14109 2 snd_hda_intel,snd_pcm
serio_raw 13032 0
lpc_ich 16993 0
i2c_algo_bit 13317 1 i915
mac_hid 13078 0
video 19117 1 i915
lp 17456 0
parport 40931 3 parport_pc,ppdev,lp
ums_realtek 17929 0
usb_storage 39720 1 ums_realtek
ahci 25621 2
libahci 26166 1 ahci
sky2 53629 0
6- Modprobing
echo "options ath9k nohwcrypt=1" | sudo tee /etc/modprobe.d/ath9k.conf
options ath9k nohwcrypt=1
sudo modprobe -rfv ath9k
rmmod /lib/modules/3.5.0-37-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k.ko
rmmod /lib/modules/3.5.0-37-generic/kernel/net/mac80211/mac80211.ko
rmmod /lib/modules/3.5.0-37-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k_common.ko
rmmod /lib/modules/3.5.0-37-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k_hw.ko
rmmod /lib/modules/3.5.0-37-generic/kernel/drivers/net/wireless/ath/ath.ko
rmmod /lib/modules/3.5.0-37-generic/kernel/net/wireless/cfg80211.ko
sudo modprobe -v ath9k
insmod /lib/modules/3.5.0-37-generic/kernel/net/wireless/cfg80211.ko
insmod /lib/modules/3.5.0-37-generic/kernel/drivers/net/wireless/ath/ath.ko
insmod /lib/modules/3.5.0-37-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k_hw.ko
insmod /lib/modules/3.5.0-37-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k_common.ko
insmod /lib/modules/3.5.0-37-generic/kernel/net/mac80211/mac80211.ko
insmod /lib/modules/3.5.0-37-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k.ko nohwcrypt=1
7- Output of dmesg | egrep 'ath|firm|wlan|network|wpa'
http://pastebin.com/ySLm71YN
Any and all help is welcome!
wireless networking drivers dell
|
show 11 more comments
I recently installed Ubuntu onto my Dell Inspiron 1545 laptop.
I can connect to the Internet via Ethernet, but wireless won't work. The prompt to put in the wifi password pops up, but when I put in the password, it simply says connecting and the prompt for the password comes back up! The prompt will come back up every two or three minutes, but the same thing happens.
I've tried to install drivers using Windows Wireless Drivers, but I can't seem to figure it out. My wireless card is an Atheros AR928X. This is my first time using Ubuntu.
Here is the output of the commands I've been asked to run:
1- Output of lspci -nnk | grep -iA2 net
$ lspci -nnk | grep -iA2 net
09:00.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8040 PCI-E Fast Ethernet Controller [11ab:4354] (rev 13)
Subsystem: Dell Device [1028:02aa]
Kernel driver in use: sky2
--
0c:00.0 Network controller [0280]: Atheros Communications Inc. AR928X Wireless Network Adapter (PCI-Express) [168c:002a] (rev 01)
Subsystem: Atheros Communications Inc. Device [168c:0200]
Kernel driver in use: ath9k
2- Output of lsusb
$ lsusb
Bus 001 Device 003: ID 0c45:63ee Microdia
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
3- Output of nm-tool
, sudo iwlist scan
and iwconfig
$ nm-tool
NetworkManager Tool
State: connected (global)
- Device: eth0 [Wired connection 1] -------------------------------------------
Type: Wired
Driver: sky2
State: connected
Default: yes
HW Address: 00:25:64:44:02:7D
Capabilities:
Carrier Detect: yes
Speed: 100 Mb/s
Wired Properties
Carrier: on
IPv4 Settings:
Address: 192.168.1.90
Prefix: 24 (255.255.255.0)
Gateway: 192.168.1.254
DNS: 192.168.1.254
DNS: 75.153.176.9
- Device: wlan0 ----------------------------------------------------------------
Type: 802.11 WiFi
Driver: ath9k
State: disconnected
Default: no
HW Address: 00:22:5F:C2:08:1F
Capabilities:
Wireless Properties
WEP Encryption: yes
WPA Encryption: yes
WPA2 Encryption: yes
Wireless Access Points
beau: Infra, 00:26:B8:ED:E6:CC, Freq 2422 MHz, Rate 54 Mb/s, Strength 95 WPA
verjee: Infra, F0:D1:A9:14:03:7A, Freq 2452 MHz, Rate 54 Mb/s, Strength 32 WPA2
$ sudo iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
wlan0 Scan completed :
Cell 01 - Address: 00:26:B8:ED:E6:CC
Channel:3
Frequency:2.422 GHz (Channel 3)
Quality=64/70 Signal level=-46 dBm
Encryption key:on
ESSID:"beau"
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s
24 Mb/s; 36 Mb/s; 54 Mb/s
Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 48 Mb/s
Mode:Master
Extra:tsf=0000024523a5e000
Extra: Last beacon: 36ms ago
IE: Unknown: 000462656175
IE: Unknown: 010882848B962430486C
IE: Unknown: 030103
IE: Unknown: 2A0100
IE: Unknown: 2F0100
IE: Unknown: 32040C121860
IE: Unknown: 2D1A6C181BFFFF000000000000000000000000000000000000000000
IE: Unknown: 3D1603001300000000000000000000000000000000000000
IE: Unknown: DD090010180202F0050000
IE: WPA Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : TKIP
IE: Unknown: DD180050F2020101800003A4000027A4000042435E0062322F00
IE: Unknown: DD1E00904C336C181BFFFF000000000000000000000000000000000000000000
IE: Unknown: DD1A00904C3403001300000000000000000000000000000000000000
Cell 02 - Address: F0:D1:A9:14:03:7A
Channel:9
Frequency:2.452 GHz (Channel 9)
Quality=27/70 Signal level=-83 dBm
Encryption key:on
ESSID:"verjee"
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
9 Mb/s; 12 Mb/s; 18 Mb/s
Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s
Mode:Master
Extra:tsf=000000173491f180
Extra: Last beacon: 3636ms ago
IE: Unknown: 00067665726A6565
IE: Unknown: 010882848B960C121824
IE: Unknown: 030109
IE: Unknown: 0706434120010B1E
IE: Unknown: 2A0100
IE: Unknown: 32043048606C
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : CCMP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : PSK
IE: Unknown: 2D1AAD511BFFFF000000000000000000000000000000000000000000
IE: Unknown: 33027E9D
IE: Unknown: 3D1609080400000000000000000000000000000000000000
IE: Unknown: 46050200010000
IE: Unknown: DD180050F2020101010003A4000027A4000042435E0062322F00
IE: Unknown: DD0700039301730B20
IE: Unknown: DD0E0017F20700010106F0D1A914037A
$ iwconfig
wlan0 IEEE 802.11abgn ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=16 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Power Management:off
lo no wireless extensions.
eth0 no wireless extensions.
Authentication Suites (1) : PSK
4- Output of rfkill list all
$ rfkill list all
0: phy0: Wireless LAN
Soft blocked: no
Hard blocked: no
5- Output of lsmod
$ lsmod
Module Size Used by
bnep 17791 2
rfcomm 38104 0
bluetooth 189625 10 bnep,rfcomm
parport_pc 32115 0
ppdev 12850 0
snd_hda_codec_idt 60238 1
arc4 12474 2
snd_hda_intel 32983 5
snd_hda_codec 116477 2 snd_hda_codec_idt,snd_hda_intel
snd_hwdep 13277 1 snd_hda_codec
joydev 17394 0
ath9k 122028 0
mac80211 475546 1 ath9k
snd_pcm 81124 3 snd_hda_intel,snd_hda_codec
snd_seq_midi 13133 0
snd_rawmidi 25426 1 snd_seq_midi
snd_seq_midi_event 14476 1 snd_seq_midi
ath9k_common 13782 1 ath9k
ath9k_hw 384090 2 ath9k,ath9k_common
i915 479235 4
uvcvideo 72249 0
snd_seq 51594 2 snd_seq_midi,snd_seq_midi_event
snd_timer 28932 2 snd_pcm,snd_seq
snd_seq_device 14138 3 snd_seq_midi,snd_rawmidi,snd_seq
videobuf2_core 32212 1 uvcvideo
ath 19436 3 ath9k,ath9k_common,ath9k_hw
drm_kms_helper 47459 1 i915
cfg80211 181041 3 ath9k,mac80211,ath
drm 240443 5 i915,drm_kms_helper
psmouse 91381 0
videodev 100265 2 uvcvideo,videobuf2_core
snd 62675 18 snd_hda_codec_idt,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
videobuf2_vmalloc 12757 1 uvcvideo
videobuf2_memops 13213 1 videobuf2_vmalloc
dell_wmi 12602 0
coretemp 13362 0
sparse_keymap 13659 1 dell_wmi
gpio_ich 13160 0
wmi 18745 1 dell_wmi
dell_laptop 17210 0
microcode 18396 0
dcdbas 14099 1 dell_laptop
soundcore 14636 1 snd
snd_page_alloc 14109 2 snd_hda_intel,snd_pcm
serio_raw 13032 0
lpc_ich 16993 0
i2c_algo_bit 13317 1 i915
mac_hid 13078 0
video 19117 1 i915
lp 17456 0
parport 40931 3 parport_pc,ppdev,lp
ums_realtek 17929 0
usb_storage 39720 1 ums_realtek
ahci 25621 2
libahci 26166 1 ahci
sky2 53629 0
6- Modprobing
echo "options ath9k nohwcrypt=1" | sudo tee /etc/modprobe.d/ath9k.conf
options ath9k nohwcrypt=1
sudo modprobe -rfv ath9k
rmmod /lib/modules/3.5.0-37-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k.ko
rmmod /lib/modules/3.5.0-37-generic/kernel/net/mac80211/mac80211.ko
rmmod /lib/modules/3.5.0-37-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k_common.ko
rmmod /lib/modules/3.5.0-37-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k_hw.ko
rmmod /lib/modules/3.5.0-37-generic/kernel/drivers/net/wireless/ath/ath.ko
rmmod /lib/modules/3.5.0-37-generic/kernel/net/wireless/cfg80211.ko
sudo modprobe -v ath9k
insmod /lib/modules/3.5.0-37-generic/kernel/net/wireless/cfg80211.ko
insmod /lib/modules/3.5.0-37-generic/kernel/drivers/net/wireless/ath/ath.ko
insmod /lib/modules/3.5.0-37-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k_hw.ko
insmod /lib/modules/3.5.0-37-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k_common.ko
insmod /lib/modules/3.5.0-37-generic/kernel/net/mac80211/mac80211.ko
insmod /lib/modules/3.5.0-37-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k.ko nohwcrypt=1
7- Output of dmesg | egrep 'ath|firm|wlan|network|wpa'
http://pastebin.com/ySLm71YN
Any and all help is welcome!
wireless networking drivers dell
Please open the terminal(ctrl+alt+t) run the commands one line at a time:lspci -nnk | grep -iA2 net
lsusb
nm-tool
sudo iwlist scan
iwconfig
rfkill list all
lsmod
post the output at pastebin.com then post the link here. Thanks
– Wild Man
Aug 7 '13 at 19:28
@WildMan, please add the commands in more readable manner! :)
– edwin
Aug 7 '13 at 19:45
pastebin.com/1pc2fNBQ
– user182232
Aug 7 '13 at 19:52
@edwin I do not know how to make the commands more readable in comments, I have tried before and this is the best I came up with.
– Wild Man
Aug 7 '13 at 21:32
Sorry, should I enter the entire "sudo cat /var/log/syslog | grep -e ath -e firmware | -e wlan -e wpa -e etork tail -n45" Or is each line a command that should be entered?
– user182232
Aug 7 '13 at 23:18
|
show 11 more comments
I recently installed Ubuntu onto my Dell Inspiron 1545 laptop.
I can connect to the Internet via Ethernet, but wireless won't work. The prompt to put in the wifi password pops up, but when I put in the password, it simply says connecting and the prompt for the password comes back up! The prompt will come back up every two or three minutes, but the same thing happens.
I've tried to install drivers using Windows Wireless Drivers, but I can't seem to figure it out. My wireless card is an Atheros AR928X. This is my first time using Ubuntu.
Here is the output of the commands I've been asked to run:
1- Output of lspci -nnk | grep -iA2 net
$ lspci -nnk | grep -iA2 net
09:00.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8040 PCI-E Fast Ethernet Controller [11ab:4354] (rev 13)
Subsystem: Dell Device [1028:02aa]
Kernel driver in use: sky2
--
0c:00.0 Network controller [0280]: Atheros Communications Inc. AR928X Wireless Network Adapter (PCI-Express) [168c:002a] (rev 01)
Subsystem: Atheros Communications Inc. Device [168c:0200]
Kernel driver in use: ath9k
2- Output of lsusb
$ lsusb
Bus 001 Device 003: ID 0c45:63ee Microdia
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
3- Output of nm-tool
, sudo iwlist scan
and iwconfig
$ nm-tool
NetworkManager Tool
State: connected (global)
- Device: eth0 [Wired connection 1] -------------------------------------------
Type: Wired
Driver: sky2
State: connected
Default: yes
HW Address: 00:25:64:44:02:7D
Capabilities:
Carrier Detect: yes
Speed: 100 Mb/s
Wired Properties
Carrier: on
IPv4 Settings:
Address: 192.168.1.90
Prefix: 24 (255.255.255.0)
Gateway: 192.168.1.254
DNS: 192.168.1.254
DNS: 75.153.176.9
- Device: wlan0 ----------------------------------------------------------------
Type: 802.11 WiFi
Driver: ath9k
State: disconnected
Default: no
HW Address: 00:22:5F:C2:08:1F
Capabilities:
Wireless Properties
WEP Encryption: yes
WPA Encryption: yes
WPA2 Encryption: yes
Wireless Access Points
beau: Infra, 00:26:B8:ED:E6:CC, Freq 2422 MHz, Rate 54 Mb/s, Strength 95 WPA
verjee: Infra, F0:D1:A9:14:03:7A, Freq 2452 MHz, Rate 54 Mb/s, Strength 32 WPA2
$ sudo iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
wlan0 Scan completed :
Cell 01 - Address: 00:26:B8:ED:E6:CC
Channel:3
Frequency:2.422 GHz (Channel 3)
Quality=64/70 Signal level=-46 dBm
Encryption key:on
ESSID:"beau"
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s
24 Mb/s; 36 Mb/s; 54 Mb/s
Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 48 Mb/s
Mode:Master
Extra:tsf=0000024523a5e000
Extra: Last beacon: 36ms ago
IE: Unknown: 000462656175
IE: Unknown: 010882848B962430486C
IE: Unknown: 030103
IE: Unknown: 2A0100
IE: Unknown: 2F0100
IE: Unknown: 32040C121860
IE: Unknown: 2D1A6C181BFFFF000000000000000000000000000000000000000000
IE: Unknown: 3D1603001300000000000000000000000000000000000000
IE: Unknown: DD090010180202F0050000
IE: WPA Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : TKIP
IE: Unknown: DD180050F2020101800003A4000027A4000042435E0062322F00
IE: Unknown: DD1E00904C336C181BFFFF000000000000000000000000000000000000000000
IE: Unknown: DD1A00904C3403001300000000000000000000000000000000000000
Cell 02 - Address: F0:D1:A9:14:03:7A
Channel:9
Frequency:2.452 GHz (Channel 9)
Quality=27/70 Signal level=-83 dBm
Encryption key:on
ESSID:"verjee"
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
9 Mb/s; 12 Mb/s; 18 Mb/s
Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s
Mode:Master
Extra:tsf=000000173491f180
Extra: Last beacon: 3636ms ago
IE: Unknown: 00067665726A6565
IE: Unknown: 010882848B960C121824
IE: Unknown: 030109
IE: Unknown: 0706434120010B1E
IE: Unknown: 2A0100
IE: Unknown: 32043048606C
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : CCMP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : PSK
IE: Unknown: 2D1AAD511BFFFF000000000000000000000000000000000000000000
IE: Unknown: 33027E9D
IE: Unknown: 3D1609080400000000000000000000000000000000000000
IE: Unknown: 46050200010000
IE: Unknown: DD180050F2020101010003A4000027A4000042435E0062322F00
IE: Unknown: DD0700039301730B20
IE: Unknown: DD0E0017F20700010106F0D1A914037A
$ iwconfig
wlan0 IEEE 802.11abgn ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=16 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Power Management:off
lo no wireless extensions.
eth0 no wireless extensions.
Authentication Suites (1) : PSK
4- Output of rfkill list all
$ rfkill list all
0: phy0: Wireless LAN
Soft blocked: no
Hard blocked: no
5- Output of lsmod
$ lsmod
Module Size Used by
bnep 17791 2
rfcomm 38104 0
bluetooth 189625 10 bnep,rfcomm
parport_pc 32115 0
ppdev 12850 0
snd_hda_codec_idt 60238 1
arc4 12474 2
snd_hda_intel 32983 5
snd_hda_codec 116477 2 snd_hda_codec_idt,snd_hda_intel
snd_hwdep 13277 1 snd_hda_codec
joydev 17394 0
ath9k 122028 0
mac80211 475546 1 ath9k
snd_pcm 81124 3 snd_hda_intel,snd_hda_codec
snd_seq_midi 13133 0
snd_rawmidi 25426 1 snd_seq_midi
snd_seq_midi_event 14476 1 snd_seq_midi
ath9k_common 13782 1 ath9k
ath9k_hw 384090 2 ath9k,ath9k_common
i915 479235 4
uvcvideo 72249 0
snd_seq 51594 2 snd_seq_midi,snd_seq_midi_event
snd_timer 28932 2 snd_pcm,snd_seq
snd_seq_device 14138 3 snd_seq_midi,snd_rawmidi,snd_seq
videobuf2_core 32212 1 uvcvideo
ath 19436 3 ath9k,ath9k_common,ath9k_hw
drm_kms_helper 47459 1 i915
cfg80211 181041 3 ath9k,mac80211,ath
drm 240443 5 i915,drm_kms_helper
psmouse 91381 0
videodev 100265 2 uvcvideo,videobuf2_core
snd 62675 18 snd_hda_codec_idt,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
videobuf2_vmalloc 12757 1 uvcvideo
videobuf2_memops 13213 1 videobuf2_vmalloc
dell_wmi 12602 0
coretemp 13362 0
sparse_keymap 13659 1 dell_wmi
gpio_ich 13160 0
wmi 18745 1 dell_wmi
dell_laptop 17210 0
microcode 18396 0
dcdbas 14099 1 dell_laptop
soundcore 14636 1 snd
snd_page_alloc 14109 2 snd_hda_intel,snd_pcm
serio_raw 13032 0
lpc_ich 16993 0
i2c_algo_bit 13317 1 i915
mac_hid 13078 0
video 19117 1 i915
lp 17456 0
parport 40931 3 parport_pc,ppdev,lp
ums_realtek 17929 0
usb_storage 39720 1 ums_realtek
ahci 25621 2
libahci 26166 1 ahci
sky2 53629 0
6- Modprobing
echo "options ath9k nohwcrypt=1" | sudo tee /etc/modprobe.d/ath9k.conf
options ath9k nohwcrypt=1
sudo modprobe -rfv ath9k
rmmod /lib/modules/3.5.0-37-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k.ko
rmmod /lib/modules/3.5.0-37-generic/kernel/net/mac80211/mac80211.ko
rmmod /lib/modules/3.5.0-37-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k_common.ko
rmmod /lib/modules/3.5.0-37-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k_hw.ko
rmmod /lib/modules/3.5.0-37-generic/kernel/drivers/net/wireless/ath/ath.ko
rmmod /lib/modules/3.5.0-37-generic/kernel/net/wireless/cfg80211.ko
sudo modprobe -v ath9k
insmod /lib/modules/3.5.0-37-generic/kernel/net/wireless/cfg80211.ko
insmod /lib/modules/3.5.0-37-generic/kernel/drivers/net/wireless/ath/ath.ko
insmod /lib/modules/3.5.0-37-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k_hw.ko
insmod /lib/modules/3.5.0-37-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k_common.ko
insmod /lib/modules/3.5.0-37-generic/kernel/net/mac80211/mac80211.ko
insmod /lib/modules/3.5.0-37-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k.ko nohwcrypt=1
7- Output of dmesg | egrep 'ath|firm|wlan|network|wpa'
http://pastebin.com/ySLm71YN
Any and all help is welcome!
wireless networking drivers dell
I recently installed Ubuntu onto my Dell Inspiron 1545 laptop.
I can connect to the Internet via Ethernet, but wireless won't work. The prompt to put in the wifi password pops up, but when I put in the password, it simply says connecting and the prompt for the password comes back up! The prompt will come back up every two or three minutes, but the same thing happens.
I've tried to install drivers using Windows Wireless Drivers, but I can't seem to figure it out. My wireless card is an Atheros AR928X. This is my first time using Ubuntu.
Here is the output of the commands I've been asked to run:
1- Output of lspci -nnk | grep -iA2 net
$ lspci -nnk | grep -iA2 net
09:00.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8040 PCI-E Fast Ethernet Controller [11ab:4354] (rev 13)
Subsystem: Dell Device [1028:02aa]
Kernel driver in use: sky2
--
0c:00.0 Network controller [0280]: Atheros Communications Inc. AR928X Wireless Network Adapter (PCI-Express) [168c:002a] (rev 01)
Subsystem: Atheros Communications Inc. Device [168c:0200]
Kernel driver in use: ath9k
2- Output of lsusb
$ lsusb
Bus 001 Device 003: ID 0c45:63ee Microdia
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
3- Output of nm-tool
, sudo iwlist scan
and iwconfig
$ nm-tool
NetworkManager Tool
State: connected (global)
- Device: eth0 [Wired connection 1] -------------------------------------------
Type: Wired
Driver: sky2
State: connected
Default: yes
HW Address: 00:25:64:44:02:7D
Capabilities:
Carrier Detect: yes
Speed: 100 Mb/s
Wired Properties
Carrier: on
IPv4 Settings:
Address: 192.168.1.90
Prefix: 24 (255.255.255.0)
Gateway: 192.168.1.254
DNS: 192.168.1.254
DNS: 75.153.176.9
- Device: wlan0 ----------------------------------------------------------------
Type: 802.11 WiFi
Driver: ath9k
State: disconnected
Default: no
HW Address: 00:22:5F:C2:08:1F
Capabilities:
Wireless Properties
WEP Encryption: yes
WPA Encryption: yes
WPA2 Encryption: yes
Wireless Access Points
beau: Infra, 00:26:B8:ED:E6:CC, Freq 2422 MHz, Rate 54 Mb/s, Strength 95 WPA
verjee: Infra, F0:D1:A9:14:03:7A, Freq 2452 MHz, Rate 54 Mb/s, Strength 32 WPA2
$ sudo iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
wlan0 Scan completed :
Cell 01 - Address: 00:26:B8:ED:E6:CC
Channel:3
Frequency:2.422 GHz (Channel 3)
Quality=64/70 Signal level=-46 dBm
Encryption key:on
ESSID:"beau"
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s
24 Mb/s; 36 Mb/s; 54 Mb/s
Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 48 Mb/s
Mode:Master
Extra:tsf=0000024523a5e000
Extra: Last beacon: 36ms ago
IE: Unknown: 000462656175
IE: Unknown: 010882848B962430486C
IE: Unknown: 030103
IE: Unknown: 2A0100
IE: Unknown: 2F0100
IE: Unknown: 32040C121860
IE: Unknown: 2D1A6C181BFFFF000000000000000000000000000000000000000000
IE: Unknown: 3D1603001300000000000000000000000000000000000000
IE: Unknown: DD090010180202F0050000
IE: WPA Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : TKIP
IE: Unknown: DD180050F2020101800003A4000027A4000042435E0062322F00
IE: Unknown: DD1E00904C336C181BFFFF000000000000000000000000000000000000000000
IE: Unknown: DD1A00904C3403001300000000000000000000000000000000000000
Cell 02 - Address: F0:D1:A9:14:03:7A
Channel:9
Frequency:2.452 GHz (Channel 9)
Quality=27/70 Signal level=-83 dBm
Encryption key:on
ESSID:"verjee"
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
9 Mb/s; 12 Mb/s; 18 Mb/s
Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s
Mode:Master
Extra:tsf=000000173491f180
Extra: Last beacon: 3636ms ago
IE: Unknown: 00067665726A6565
IE: Unknown: 010882848B960C121824
IE: Unknown: 030109
IE: Unknown: 0706434120010B1E
IE: Unknown: 2A0100
IE: Unknown: 32043048606C
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : CCMP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : PSK
IE: Unknown: 2D1AAD511BFFFF000000000000000000000000000000000000000000
IE: Unknown: 33027E9D
IE: Unknown: 3D1609080400000000000000000000000000000000000000
IE: Unknown: 46050200010000
IE: Unknown: DD180050F2020101010003A4000027A4000042435E0062322F00
IE: Unknown: DD0700039301730B20
IE: Unknown: DD0E0017F20700010106F0D1A914037A
$ iwconfig
wlan0 IEEE 802.11abgn ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=16 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Power Management:off
lo no wireless extensions.
eth0 no wireless extensions.
Authentication Suites (1) : PSK
4- Output of rfkill list all
$ rfkill list all
0: phy0: Wireless LAN
Soft blocked: no
Hard blocked: no
5- Output of lsmod
$ lsmod
Module Size Used by
bnep 17791 2
rfcomm 38104 0
bluetooth 189625 10 bnep,rfcomm
parport_pc 32115 0
ppdev 12850 0
snd_hda_codec_idt 60238 1
arc4 12474 2
snd_hda_intel 32983 5
snd_hda_codec 116477 2 snd_hda_codec_idt,snd_hda_intel
snd_hwdep 13277 1 snd_hda_codec
joydev 17394 0
ath9k 122028 0
mac80211 475546 1 ath9k
snd_pcm 81124 3 snd_hda_intel,snd_hda_codec
snd_seq_midi 13133 0
snd_rawmidi 25426 1 snd_seq_midi
snd_seq_midi_event 14476 1 snd_seq_midi
ath9k_common 13782 1 ath9k
ath9k_hw 384090 2 ath9k,ath9k_common
i915 479235 4
uvcvideo 72249 0
snd_seq 51594 2 snd_seq_midi,snd_seq_midi_event
snd_timer 28932 2 snd_pcm,snd_seq
snd_seq_device 14138 3 snd_seq_midi,snd_rawmidi,snd_seq
videobuf2_core 32212 1 uvcvideo
ath 19436 3 ath9k,ath9k_common,ath9k_hw
drm_kms_helper 47459 1 i915
cfg80211 181041 3 ath9k,mac80211,ath
drm 240443 5 i915,drm_kms_helper
psmouse 91381 0
videodev 100265 2 uvcvideo,videobuf2_core
snd 62675 18 snd_hda_codec_idt,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
videobuf2_vmalloc 12757 1 uvcvideo
videobuf2_memops 13213 1 videobuf2_vmalloc
dell_wmi 12602 0
coretemp 13362 0
sparse_keymap 13659 1 dell_wmi
gpio_ich 13160 0
wmi 18745 1 dell_wmi
dell_laptop 17210 0
microcode 18396 0
dcdbas 14099 1 dell_laptop
soundcore 14636 1 snd
snd_page_alloc 14109 2 snd_hda_intel,snd_pcm
serio_raw 13032 0
lpc_ich 16993 0
i2c_algo_bit 13317 1 i915
mac_hid 13078 0
video 19117 1 i915
lp 17456 0
parport 40931 3 parport_pc,ppdev,lp
ums_realtek 17929 0
usb_storage 39720 1 ums_realtek
ahci 25621 2
libahci 26166 1 ahci
sky2 53629 0
6- Modprobing
echo "options ath9k nohwcrypt=1" | sudo tee /etc/modprobe.d/ath9k.conf
options ath9k nohwcrypt=1
sudo modprobe -rfv ath9k
rmmod /lib/modules/3.5.0-37-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k.ko
rmmod /lib/modules/3.5.0-37-generic/kernel/net/mac80211/mac80211.ko
rmmod /lib/modules/3.5.0-37-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k_common.ko
rmmod /lib/modules/3.5.0-37-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k_hw.ko
rmmod /lib/modules/3.5.0-37-generic/kernel/drivers/net/wireless/ath/ath.ko
rmmod /lib/modules/3.5.0-37-generic/kernel/net/wireless/cfg80211.ko
sudo modprobe -v ath9k
insmod /lib/modules/3.5.0-37-generic/kernel/net/wireless/cfg80211.ko
insmod /lib/modules/3.5.0-37-generic/kernel/drivers/net/wireless/ath/ath.ko
insmod /lib/modules/3.5.0-37-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k_hw.ko
insmod /lib/modules/3.5.0-37-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k_common.ko
insmod /lib/modules/3.5.0-37-generic/kernel/net/mac80211/mac80211.ko
insmod /lib/modules/3.5.0-37-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k.ko nohwcrypt=1
7- Output of dmesg | egrep 'ath|firm|wlan|network|wpa'
http://pastebin.com/ySLm71YN
Any and all help is welcome!
wireless networking drivers dell
wireless networking drivers dell
edited Aug 8 '13 at 3:21
user182232
asked Aug 7 '13 at 19:16
user182232user182232
16115
16115
Please open the terminal(ctrl+alt+t) run the commands one line at a time:lspci -nnk | grep -iA2 net
lsusb
nm-tool
sudo iwlist scan
iwconfig
rfkill list all
lsmod
post the output at pastebin.com then post the link here. Thanks
– Wild Man
Aug 7 '13 at 19:28
@WildMan, please add the commands in more readable manner! :)
– edwin
Aug 7 '13 at 19:45
pastebin.com/1pc2fNBQ
– user182232
Aug 7 '13 at 19:52
@edwin I do not know how to make the commands more readable in comments, I have tried before and this is the best I came up with.
– Wild Man
Aug 7 '13 at 21:32
Sorry, should I enter the entire "sudo cat /var/log/syslog | grep -e ath -e firmware | -e wlan -e wpa -e etork tail -n45" Or is each line a command that should be entered?
– user182232
Aug 7 '13 at 23:18
|
show 11 more comments
Please open the terminal(ctrl+alt+t) run the commands one line at a time:lspci -nnk | grep -iA2 net
lsusb
nm-tool
sudo iwlist scan
iwconfig
rfkill list all
lsmod
post the output at pastebin.com then post the link here. Thanks
– Wild Man
Aug 7 '13 at 19:28
@WildMan, please add the commands in more readable manner! :)
– edwin
Aug 7 '13 at 19:45
pastebin.com/1pc2fNBQ
– user182232
Aug 7 '13 at 19:52
@edwin I do not know how to make the commands more readable in comments, I have tried before and this is the best I came up with.
– Wild Man
Aug 7 '13 at 21:32
Sorry, should I enter the entire "sudo cat /var/log/syslog | grep -e ath -e firmware | -e wlan -e wpa -e etork tail -n45" Or is each line a command that should be entered?
– user182232
Aug 7 '13 at 23:18
Please open the terminal(ctrl+alt+t) run the commands one line at a time:
lspci -nnk | grep -iA2 net
lsusb
nm-tool
sudo iwlist scan
iwconfig
rfkill list all
lsmod
post the output at pastebin.com then post the link here. Thanks– Wild Man
Aug 7 '13 at 19:28
Please open the terminal(ctrl+alt+t) run the commands one line at a time:
lspci -nnk | grep -iA2 net
lsusb
nm-tool
sudo iwlist scan
iwconfig
rfkill list all
lsmod
post the output at pastebin.com then post the link here. Thanks– Wild Man
Aug 7 '13 at 19:28
@WildMan, please add the commands in more readable manner! :)
– edwin
Aug 7 '13 at 19:45
@WildMan, please add the commands in more readable manner! :)
– edwin
Aug 7 '13 at 19:45
pastebin.com/1pc2fNBQ
– user182232
Aug 7 '13 at 19:52
pastebin.com/1pc2fNBQ
– user182232
Aug 7 '13 at 19:52
@edwin I do not know how to make the commands more readable in comments, I have tried before and this is the best I came up with.
– Wild Man
Aug 7 '13 at 21:32
@edwin I do not know how to make the commands more readable in comments, I have tried before and this is the best I came up with.
– Wild Man
Aug 7 '13 at 21:32
Sorry, should I enter the entire "sudo cat /var/log/syslog | grep -e ath -e firmware | -e wlan -e wpa -e etork tail -n45" Or is each line a command that should be entered?
– user182232
Aug 7 '13 at 23:18
Sorry, should I enter the entire "sudo cat /var/log/syslog | grep -e ath -e firmware | -e wlan -e wpa -e etork tail -n45" Or is each line a command that should be entered?
– user182232
Aug 7 '13 at 23:18
|
show 11 more comments
3 Answers
3
active
oldest
votes
I had this same issue with a RealTek RTL8188EEE wireless card and Ubuntu 13.04. The quick solution was to just put in the IP of my Wireless Router, then change it from AES to TKIP-AES. This kept the other systems on my wireless happy, and suddenly Ubuntu took the password and connected me with a reported 72Mb/s connection speed.
I couldn't do too much more since I was running from the DVD, making sure it works before I install. I had seen suggestions of doing NDISWrapper and then rebooting - not gonna help with the DVD.
Hope this helps anyone else looking. Probably too late to help the original person posting, but maybe it will help someone else. If you can't do TKIP-AES, try going from AES to just TKIP. That was suggested in another forum as well.
Yep, this did it for me. I changed my router to use TKIP instead of AES.
– Mirthquakes
Sep 28 '14 at 20:41
add a comment |
Please copy and paste the commands for accuracy one line at a time:
echo "options ath9k nohwcrypt=1" | sudo tee /etc/modprobe.d/ath9k.conf
sudo modprobe -rfv ath9k
sudo modprobe -v ath9k
Also it would be best to set encryption in the router to just wpa2 if you have that option by entering 192.168.0.1 or something very similar to those numbers in your web browser while having an ethernet connection, you may have to look at the documentation for your router for the exact numbers to enter.
Also try channel 1 or 11 in your router.
You can google the documentation for your router.
Please set your wireless settings in network manager to match the screenshots.
You should also remove your connection in network manager and reset your router then reboot your computer.
pastebin.com/2fjtMnPy
– user182232
Aug 7 '13 at 21:29
Cant seem to find the router documents at the moment. Will comment if found. (Thanks for the help btw)
– user182232
Aug 7 '13 at 21:30
I would run the commands and see if that makes it connect then you can look up router documentation if needed.
– Wild Man
Aug 7 '13 at 21:34
Wireless still not connecting. I still can't find the documents. Any other suggestions?
– user182232
Aug 7 '13 at 21:59
I've gone through the entire answer, step by step, but the wireless won't connect. I think here is where I admit defeat. Thank you all, especially Wild Man,for all the help. I think I have to crawl back to Windows now... Again, thanks for all the help. You guys were awesome!
– user182232
Aug 8 '13 at 17:56
add a comment |
Make sure you have wireless-tools installed via sudo apt-get install wireless-tools
This will provide a better GUI to connect to existing wireless networks.
Try pinging any site, local computer or not, to test if it is working. You may get a specific error, which may mean that some of the settings are off.
When put into the terminal, it comes back saying that the wireless tools are already the newest version.
– user182232
Aug 7 '13 at 22:10
What Ubuntu version are you using, and what desktop environment? (Unity is default, if you just installed)
– Mobo
Aug 7 '13 at 22:20
Version 12.04 LTS. I am assuming that the desktop environment is "Unity" as I don't recall making any changes like that.
– user182232
Aug 7 '13 at 22:23
add a comment |
Your Answer
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "89"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: true,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: 10,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2faskubuntu.com%2fquestions%2f329871%2fwireless-wont-connect%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
3 Answers
3
active
oldest
votes
3 Answers
3
active
oldest
votes
active
oldest
votes
active
oldest
votes
I had this same issue with a RealTek RTL8188EEE wireless card and Ubuntu 13.04. The quick solution was to just put in the IP of my Wireless Router, then change it from AES to TKIP-AES. This kept the other systems on my wireless happy, and suddenly Ubuntu took the password and connected me with a reported 72Mb/s connection speed.
I couldn't do too much more since I was running from the DVD, making sure it works before I install. I had seen suggestions of doing NDISWrapper and then rebooting - not gonna help with the DVD.
Hope this helps anyone else looking. Probably too late to help the original person posting, but maybe it will help someone else. If you can't do TKIP-AES, try going from AES to just TKIP. That was suggested in another forum as well.
Yep, this did it for me. I changed my router to use TKIP instead of AES.
– Mirthquakes
Sep 28 '14 at 20:41
add a comment |
I had this same issue with a RealTek RTL8188EEE wireless card and Ubuntu 13.04. The quick solution was to just put in the IP of my Wireless Router, then change it from AES to TKIP-AES. This kept the other systems on my wireless happy, and suddenly Ubuntu took the password and connected me with a reported 72Mb/s connection speed.
I couldn't do too much more since I was running from the DVD, making sure it works before I install. I had seen suggestions of doing NDISWrapper and then rebooting - not gonna help with the DVD.
Hope this helps anyone else looking. Probably too late to help the original person posting, but maybe it will help someone else. If you can't do TKIP-AES, try going from AES to just TKIP. That was suggested in another forum as well.
Yep, this did it for me. I changed my router to use TKIP instead of AES.
– Mirthquakes
Sep 28 '14 at 20:41
add a comment |
I had this same issue with a RealTek RTL8188EEE wireless card and Ubuntu 13.04. The quick solution was to just put in the IP of my Wireless Router, then change it from AES to TKIP-AES. This kept the other systems on my wireless happy, and suddenly Ubuntu took the password and connected me with a reported 72Mb/s connection speed.
I couldn't do too much more since I was running from the DVD, making sure it works before I install. I had seen suggestions of doing NDISWrapper and then rebooting - not gonna help with the DVD.
Hope this helps anyone else looking. Probably too late to help the original person posting, but maybe it will help someone else. If you can't do TKIP-AES, try going from AES to just TKIP. That was suggested in another forum as well.
I had this same issue with a RealTek RTL8188EEE wireless card and Ubuntu 13.04. The quick solution was to just put in the IP of my Wireless Router, then change it from AES to TKIP-AES. This kept the other systems on my wireless happy, and suddenly Ubuntu took the password and connected me with a reported 72Mb/s connection speed.
I couldn't do too much more since I was running from the DVD, making sure it works before I install. I had seen suggestions of doing NDISWrapper and then rebooting - not gonna help with the DVD.
Hope this helps anyone else looking. Probably too late to help the original person posting, but maybe it will help someone else. If you can't do TKIP-AES, try going from AES to just TKIP. That was suggested in another forum as well.
answered Feb 20 '14 at 1:19
herdivetherdivet
213
213
Yep, this did it for me. I changed my router to use TKIP instead of AES.
– Mirthquakes
Sep 28 '14 at 20:41
add a comment |
Yep, this did it for me. I changed my router to use TKIP instead of AES.
– Mirthquakes
Sep 28 '14 at 20:41
Yep, this did it for me. I changed my router to use TKIP instead of AES.
– Mirthquakes
Sep 28 '14 at 20:41
Yep, this did it for me. I changed my router to use TKIP instead of AES.
– Mirthquakes
Sep 28 '14 at 20:41
add a comment |
Please copy and paste the commands for accuracy one line at a time:
echo "options ath9k nohwcrypt=1" | sudo tee /etc/modprobe.d/ath9k.conf
sudo modprobe -rfv ath9k
sudo modprobe -v ath9k
Also it would be best to set encryption in the router to just wpa2 if you have that option by entering 192.168.0.1 or something very similar to those numbers in your web browser while having an ethernet connection, you may have to look at the documentation for your router for the exact numbers to enter.
Also try channel 1 or 11 in your router.
You can google the documentation for your router.
Please set your wireless settings in network manager to match the screenshots.
You should also remove your connection in network manager and reset your router then reboot your computer.
pastebin.com/2fjtMnPy
– user182232
Aug 7 '13 at 21:29
Cant seem to find the router documents at the moment. Will comment if found. (Thanks for the help btw)
– user182232
Aug 7 '13 at 21:30
I would run the commands and see if that makes it connect then you can look up router documentation if needed.
– Wild Man
Aug 7 '13 at 21:34
Wireless still not connecting. I still can't find the documents. Any other suggestions?
– user182232
Aug 7 '13 at 21:59
I've gone through the entire answer, step by step, but the wireless won't connect. I think here is where I admit defeat. Thank you all, especially Wild Man,for all the help. I think I have to crawl back to Windows now... Again, thanks for all the help. You guys were awesome!
– user182232
Aug 8 '13 at 17:56
add a comment |
Please copy and paste the commands for accuracy one line at a time:
echo "options ath9k nohwcrypt=1" | sudo tee /etc/modprobe.d/ath9k.conf
sudo modprobe -rfv ath9k
sudo modprobe -v ath9k
Also it would be best to set encryption in the router to just wpa2 if you have that option by entering 192.168.0.1 or something very similar to those numbers in your web browser while having an ethernet connection, you may have to look at the documentation for your router for the exact numbers to enter.
Also try channel 1 or 11 in your router.
You can google the documentation for your router.
Please set your wireless settings in network manager to match the screenshots.
You should also remove your connection in network manager and reset your router then reboot your computer.
pastebin.com/2fjtMnPy
– user182232
Aug 7 '13 at 21:29
Cant seem to find the router documents at the moment. Will comment if found. (Thanks for the help btw)
– user182232
Aug 7 '13 at 21:30
I would run the commands and see if that makes it connect then you can look up router documentation if needed.
– Wild Man
Aug 7 '13 at 21:34
Wireless still not connecting. I still can't find the documents. Any other suggestions?
– user182232
Aug 7 '13 at 21:59
I've gone through the entire answer, step by step, but the wireless won't connect. I think here is where I admit defeat. Thank you all, especially Wild Man,for all the help. I think I have to crawl back to Windows now... Again, thanks for all the help. You guys were awesome!
– user182232
Aug 8 '13 at 17:56
add a comment |
Please copy and paste the commands for accuracy one line at a time:
echo "options ath9k nohwcrypt=1" | sudo tee /etc/modprobe.d/ath9k.conf
sudo modprobe -rfv ath9k
sudo modprobe -v ath9k
Also it would be best to set encryption in the router to just wpa2 if you have that option by entering 192.168.0.1 or something very similar to those numbers in your web browser while having an ethernet connection, you may have to look at the documentation for your router for the exact numbers to enter.
Also try channel 1 or 11 in your router.
You can google the documentation for your router.
Please set your wireless settings in network manager to match the screenshots.
You should also remove your connection in network manager and reset your router then reboot your computer.
Please copy and paste the commands for accuracy one line at a time:
echo "options ath9k nohwcrypt=1" | sudo tee /etc/modprobe.d/ath9k.conf
sudo modprobe -rfv ath9k
sudo modprobe -v ath9k
Also it would be best to set encryption in the router to just wpa2 if you have that option by entering 192.168.0.1 or something very similar to those numbers in your web browser while having an ethernet connection, you may have to look at the documentation for your router for the exact numbers to enter.
Also try channel 1 or 11 in your router.
You can google the documentation for your router.
Please set your wireless settings in network manager to match the screenshots.
You should also remove your connection in network manager and reset your router then reboot your computer.
edited Aug 8 '13 at 3:56
answered Aug 7 '13 at 20:45
Wild ManWild Man
6,55732640
6,55732640
pastebin.com/2fjtMnPy
– user182232
Aug 7 '13 at 21:29
Cant seem to find the router documents at the moment. Will comment if found. (Thanks for the help btw)
– user182232
Aug 7 '13 at 21:30
I would run the commands and see if that makes it connect then you can look up router documentation if needed.
– Wild Man
Aug 7 '13 at 21:34
Wireless still not connecting. I still can't find the documents. Any other suggestions?
– user182232
Aug 7 '13 at 21:59
I've gone through the entire answer, step by step, but the wireless won't connect. I think here is where I admit defeat. Thank you all, especially Wild Man,for all the help. I think I have to crawl back to Windows now... Again, thanks for all the help. You guys were awesome!
– user182232
Aug 8 '13 at 17:56
add a comment |
pastebin.com/2fjtMnPy
– user182232
Aug 7 '13 at 21:29
Cant seem to find the router documents at the moment. Will comment if found. (Thanks for the help btw)
– user182232
Aug 7 '13 at 21:30
I would run the commands and see if that makes it connect then you can look up router documentation if needed.
– Wild Man
Aug 7 '13 at 21:34
Wireless still not connecting. I still can't find the documents. Any other suggestions?
– user182232
Aug 7 '13 at 21:59
I've gone through the entire answer, step by step, but the wireless won't connect. I think here is where I admit defeat. Thank you all, especially Wild Man,for all the help. I think I have to crawl back to Windows now... Again, thanks for all the help. You guys were awesome!
– user182232
Aug 8 '13 at 17:56
pastebin.com/2fjtMnPy
– user182232
Aug 7 '13 at 21:29
pastebin.com/2fjtMnPy
– user182232
Aug 7 '13 at 21:29
Cant seem to find the router documents at the moment. Will comment if found. (Thanks for the help btw)
– user182232
Aug 7 '13 at 21:30
Cant seem to find the router documents at the moment. Will comment if found. (Thanks for the help btw)
– user182232
Aug 7 '13 at 21:30
I would run the commands and see if that makes it connect then you can look up router documentation if needed.
– Wild Man
Aug 7 '13 at 21:34
I would run the commands and see if that makes it connect then you can look up router documentation if needed.
– Wild Man
Aug 7 '13 at 21:34
Wireless still not connecting. I still can't find the documents. Any other suggestions?
– user182232
Aug 7 '13 at 21:59
Wireless still not connecting. I still can't find the documents. Any other suggestions?
– user182232
Aug 7 '13 at 21:59
I've gone through the entire answer, step by step, but the wireless won't connect. I think here is where I admit defeat. Thank you all, especially Wild Man,for all the help. I think I have to crawl back to Windows now... Again, thanks for all the help. You guys were awesome!
– user182232
Aug 8 '13 at 17:56
I've gone through the entire answer, step by step, but the wireless won't connect. I think here is where I admit defeat. Thank you all, especially Wild Man,for all the help. I think I have to crawl back to Windows now... Again, thanks for all the help. You guys were awesome!
– user182232
Aug 8 '13 at 17:56
add a comment |
Make sure you have wireless-tools installed via sudo apt-get install wireless-tools
This will provide a better GUI to connect to existing wireless networks.
Try pinging any site, local computer or not, to test if it is working. You may get a specific error, which may mean that some of the settings are off.
When put into the terminal, it comes back saying that the wireless tools are already the newest version.
– user182232
Aug 7 '13 at 22:10
What Ubuntu version are you using, and what desktop environment? (Unity is default, if you just installed)
– Mobo
Aug 7 '13 at 22:20
Version 12.04 LTS. I am assuming that the desktop environment is "Unity" as I don't recall making any changes like that.
– user182232
Aug 7 '13 at 22:23
add a comment |
Make sure you have wireless-tools installed via sudo apt-get install wireless-tools
This will provide a better GUI to connect to existing wireless networks.
Try pinging any site, local computer or not, to test if it is working. You may get a specific error, which may mean that some of the settings are off.
When put into the terminal, it comes back saying that the wireless tools are already the newest version.
– user182232
Aug 7 '13 at 22:10
What Ubuntu version are you using, and what desktop environment? (Unity is default, if you just installed)
– Mobo
Aug 7 '13 at 22:20
Version 12.04 LTS. I am assuming that the desktop environment is "Unity" as I don't recall making any changes like that.
– user182232
Aug 7 '13 at 22:23
add a comment |
Make sure you have wireless-tools installed via sudo apt-get install wireless-tools
This will provide a better GUI to connect to existing wireless networks.
Try pinging any site, local computer or not, to test if it is working. You may get a specific error, which may mean that some of the settings are off.
Make sure you have wireless-tools installed via sudo apt-get install wireless-tools
This will provide a better GUI to connect to existing wireless networks.
Try pinging any site, local computer or not, to test if it is working. You may get a specific error, which may mean that some of the settings are off.
answered Aug 7 '13 at 22:03
MoboMobo
116214
116214
When put into the terminal, it comes back saying that the wireless tools are already the newest version.
– user182232
Aug 7 '13 at 22:10
What Ubuntu version are you using, and what desktop environment? (Unity is default, if you just installed)
– Mobo
Aug 7 '13 at 22:20
Version 12.04 LTS. I am assuming that the desktop environment is "Unity" as I don't recall making any changes like that.
– user182232
Aug 7 '13 at 22:23
add a comment |
When put into the terminal, it comes back saying that the wireless tools are already the newest version.
– user182232
Aug 7 '13 at 22:10
What Ubuntu version are you using, and what desktop environment? (Unity is default, if you just installed)
– Mobo
Aug 7 '13 at 22:20
Version 12.04 LTS. I am assuming that the desktop environment is "Unity" as I don't recall making any changes like that.
– user182232
Aug 7 '13 at 22:23
When put into the terminal, it comes back saying that the wireless tools are already the newest version.
– user182232
Aug 7 '13 at 22:10
When put into the terminal, it comes back saying that the wireless tools are already the newest version.
– user182232
Aug 7 '13 at 22:10
What Ubuntu version are you using, and what desktop environment? (Unity is default, if you just installed)
– Mobo
Aug 7 '13 at 22:20
What Ubuntu version are you using, and what desktop environment? (Unity is default, if you just installed)
– Mobo
Aug 7 '13 at 22:20
Version 12.04 LTS. I am assuming that the desktop environment is "Unity" as I don't recall making any changes like that.
– user182232
Aug 7 '13 at 22:23
Version 12.04 LTS. I am assuming that the desktop environment is "Unity" as I don't recall making any changes like that.
– user182232
Aug 7 '13 at 22:23
add a comment |
Thanks for contributing an answer to Ask Ubuntu!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2faskubuntu.com%2fquestions%2f329871%2fwireless-wont-connect%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Please open the terminal(ctrl+alt+t) run the commands one line at a time:
lspci -nnk | grep -iA2 net
lsusb
nm-tool
sudo iwlist scan
iwconfig
rfkill list all
lsmod
post the output at pastebin.com then post the link here. Thanks– Wild Man
Aug 7 '13 at 19:28
@WildMan, please add the commands in more readable manner! :)
– edwin
Aug 7 '13 at 19:45
pastebin.com/1pc2fNBQ
– user182232
Aug 7 '13 at 19:52
@edwin I do not know how to make the commands more readable in comments, I have tried before and this is the best I came up with.
– Wild Man
Aug 7 '13 at 21:32
Sorry, should I enter the entire "sudo cat /var/log/syslog | grep -e ath -e firmware | -e wlan -e wpa -e etork tail -n45" Or is each line a command that should be entered?
– user182232
Aug 7 '13 at 23:18