What is the meaning of M in the Z80 statement ADD A,M
up vote
1
down vote
favorite
Recently I have been trying to compile CP/M 2.2 from source. When I try to assemble, everything works except for the instructions ADD A,M and SBC A,M, which the assembler returns a syntax error. I have not done much Z80, so I am a little confused on what the source code means by M?
I am using the CP/M 2.2 Source (Z80 Mnemonics) from the Unofficial CP/M Website.
z80 assembly cp-m
edited 3 hours ago
Alex Hajnal
3,45031632
asked 5 hours ago
tergav17
61
New contributor
tergav17 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
add a comment |
up vote
1
down vote
favorite
Recently I have been trying to compile CP/M 2.2 from source. When I try to assemble, everything works except for the instructions ADD A,M and SBC A,M, which the assembler returns a syntax error. I have not done much Z80, so I am a little confused on what the source code means by M?
I am using the CP/M 2.2 Source (Z80 Mnemonics) from the Unofficial CP/M Website.
z80 assembly cp-m
edited 3 hours ago
Alex Hajnal
3,45031632
asked 5 hours ago
tergav17
61
New contributor
tergav17 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
It might be helpful if you link the source in question and explain where you acquired it.
– Raffzahn
5 hours ago
add a comment |
up vote
1
down vote
favorite
up vote
1
down vote
favorite
Recently I have been trying to compile CP/M 2.2 from source. When I try to assemble, everything works except for the instructions ADD A,M and SBC A,M, which the assembler returns a syntax error. I have not done much Z80, so I am a little confused on what the source code means by M?
I am using the CP/M 2.2 Source (Z80 Mnemonics) from the Unofficial CP/M Website.
z80 assembly cp-m
edited 3 hours ago
Alex Hajnal
3,45031632
asked 5 hours ago
tergav17
61
New contributor
tergav17 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
Recently I have been trying to compile CP/M 2.2 from source. When I try to assemble, everything works except for the instructions ADD A,M and SBC A,M, which the assembler returns a syntax error. I have not done much Z80, so I am a little confused on what the source code means by M?
I am using the CP/M 2.2 Source (Z80 Mnemonics) from the Unofficial CP/M Website.
z80 assembly cp-m
z80 assembly cp-m
edited 3 hours ago
Alex Hajnal
3,45031632
asked 5 hours ago
tergav17
61
New contributor
tergav17 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
edited 3 hours ago
Alex Hajnal
3,45031632
asked 5 hours ago
tergav17
61
New contributor
tergav17 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
edited 3 hours ago
Alex Hajnal
3,45031632
edited 3 hours ago
Alex Hajnal
3,45031632
edited 3 hours ago
Alex Hajnal
3,45031632
3,45031632
asked 5 hours ago
tergav17
61
New contributor
tergav17 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked 5 hours ago
tergav17
61
asked 5 hours ago
tergav17
61
61
New contributor
tergav17 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
New contributor
tergav17 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
tergav17 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
It might be helpful if you link the source in question and explain where you acquired it.
– Raffzahn
5 hours ago
add a comment |
It might be helpful if you link the source in question and explain where you acquired it.
– Raffzahn
5 hours ago
It might be helpful if you link the source in question and explain where you acquired it.
– Raffzahn
5 hours ago
It might be helpful if you link the source in question and explain where you acquired it.
– Raffzahn
5 hours ago
add a comment |
2 Answers
2
active
oldest
votes
up vote
2
down vote
In 8080 Assembler M is the memory referenced to by HL.
Depending on the assembler used this would be written as
ADD M(Original Intel 8080 syntax) or
ADD A,M(Later Intel syntax as used for example by CP/M's own ASM (*1))
The Z80 assembler equivalent would be
ADD A,(HL)(Zilog notation)
Are you sure the source you're compiling made for the Z80 (and a Z80 assembler) at all?
CP/M is by default writen in 8080 Assembly, not Z80 or any other substitute. It would make sense that the source you got is meant to be compiled with ASM, as this was the default assembler for CP/M. It would be unusual if it's formated for any later (Z80) assembler.
Wiki got some condensed remarks about the changes Zilog made to the 8080 Assembly Syntax, like the usage of full register as you might have expected in this example. DR's ASM was an inbetween product, adhering (mostly) to Intel syntax while supporting the Z80 as well.
*1 - Later assemblers where often able to compile 8080 as well as Z80 but using 8080 notaton.
answered 5 hours ago
Raffzahn
44.5k5102179
add a comment |
up vote
1
down vote
Depending on the compiler you use, you may need to explicitly state using preprocessor directives that you use 8080 commands. M80 uses .z80 and .8080 to instruct using respective instruction set mnemonics. See https://www.classic-computers.org.nz/system-80/software-manuals/manuals-Macro-80-Assembler.pdf page 20 (16 on the document's page).
If it will not compile in 8080 mode (due to Z80 directives in the source), then it means that sources are altered.The easiest way is to replace M with (HL), but I would not be surprised if resulting executable will not work properly at all.
answered 19 mins ago
Anonymous
83316
add a comment |
Your Answer
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "648"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
noCode: true, onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
tergav17 is a new contributor. Be nice, and check out our Code of Conduct.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fretrocomputing.stackexchange.com%2fquestions%2f8546%2fwhat-is-the-meaning-of-m-in-the-z80-statement-add-a-m%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
2 Answers
2
active
oldest
votes
2 Answers
2
active
oldest
votes
active
oldest
votes
active
oldest
votes
up vote
2
down vote
In 8080 Assembler M is the memory referenced to by HL.
Depending on the assembler used this would be written as
ADD M(Original Intel 8080 syntax) or
ADD A,M(Later Intel syntax as used for example by CP/M's own ASM (*1))
The Z80 assembler equivalent would be
ADD A,(HL)(Zilog notation)
Are you sure the source you're compiling made for the Z80 (and a Z80 assembler) at all?
CP/M is by default writen in 8080 Assembly, not Z80 or any other substitute. It would make sense that the source you got is meant to be compiled with ASM, as this was the default assembler for CP/M. It would be unusual if it's formated for any later (Z80) assembler.
Wiki got some condensed remarks about the changes Zilog made to the 8080 Assembly Syntax, like the usage of full register as you might have expected in this example. DR's ASM was an inbetween product, adhering (mostly) to Intel syntax while supporting the Z80 as well.
*1 - Later assemblers where often able to compile 8080 as well as Z80 but using 8080 notaton.
answered 5 hours ago
Raffzahn
44.5k5102179
add a comment |
up vote
2
down vote
In 8080 Assembler M is the memory referenced to by HL.
Depending on the assembler used this would be written as
ADD M(Original Intel 8080 syntax) or
ADD A,M(Later Intel syntax as used for example by CP/M's own ASM (*1))
The Z80 assembler equivalent would be
ADD A,(HL)(Zilog notation)
Are you sure the source you're compiling made for the Z80 (and a Z80 assembler) at all?
CP/M is by default writen in 8080 Assembly, not Z80 or any other substitute. It would make sense that the source you got is meant to be compiled with ASM, as this was the default assembler for CP/M. It would be unusual if it's formated for any later (Z80) assembler.
Wiki got some condensed remarks about the changes Zilog made to the 8080 Assembly Syntax, like the usage of full register as you might have expected in this example. DR's ASM was an inbetween product, adhering (mostly) to Intel syntax while supporting the Z80 as well.
*1 - Later assemblers where often able to compile 8080 as well as Z80 but using 8080 notaton.
answered 5 hours ago
Raffzahn
44.5k5102179
add a comment |
up vote
2
down vote
up vote
2
down vote
In 8080 Assembler M is the memory referenced to by HL.
Depending on the assembler used this would be written as
ADD M(Original Intel 8080 syntax) or
ADD A,M(Later Intel syntax as used for example by CP/M's own ASM (*1))
The Z80 assembler equivalent would be
ADD A,(HL)(Zilog notation)
Are you sure the source you're compiling made for the Z80 (and a Z80 assembler) at all?
CP/M is by default writen in 8080 Assembly, not Z80 or any other substitute. It would make sense that the source you got is meant to be compiled with ASM, as this was the default assembler for CP/M. It would be unusual if it's formated for any later (Z80) assembler.
Wiki got some condensed remarks about the changes Zilog made to the 8080 Assembly Syntax, like the usage of full register as you might have expected in this example. DR's ASM was an inbetween product, adhering (mostly) to Intel syntax while supporting the Z80 as well.
*1 - Later assemblers where often able to compile 8080 as well as Z80 but using 8080 notaton.
answered 5 hours ago
Raffzahn
44.5k5102179
In 8080 Assembler M is the memory referenced to by HL.
Depending on the assembler used this would be written as
ADD M(Original Intel 8080 syntax) or
ADD A,M(Later Intel syntax as used for example by CP/M's own ASM (*1))
The Z80 assembler equivalent would be
ADD A,(HL)(Zilog notation)
Are you sure the source you're compiling made for the Z80 (and a Z80 assembler) at all?
CP/M is by default writen in 8080 Assembly, not Z80 or any other substitute. It would make sense that the source you got is meant to be compiled with ASM, as this was the default assembler for CP/M. It would be unusual if it's formated for any later (Z80) assembler.
Wiki got some condensed remarks about the changes Zilog made to the 8080 Assembly Syntax, like the usage of full register as you might have expected in this example. DR's ASM was an inbetween product, adhering (mostly) to Intel syntax while supporting the Z80 as well.
*1 - Later assemblers where often able to compile 8080 as well as Z80 but using 8080 notaton.
answered 5 hours ago
Raffzahn
44.5k5102179
edited 4 hours ago
answered 5 hours ago
Raffzahn
44.5k5102179
answered 5 hours ago
Raffzahn
44.5k5102179
answered 5 hours ago
Raffzahn
44.5k5102179
44.5k5102179
add a comment |
add a comment |
up vote
1
down vote
Depending on the compiler you use, you may need to explicitly state using preprocessor directives that you use 8080 commands. M80 uses .z80 and .8080 to instruct using respective instruction set mnemonics. See https://www.classic-computers.org.nz/system-80/software-manuals/manuals-Macro-80-Assembler.pdf page 20 (16 on the document's page).
If it will not compile in 8080 mode (due to Z80 directives in the source), then it means that sources are altered.The easiest way is to replace M with (HL), but I would not be surprised if resulting executable will not work properly at all.
answered 19 mins ago
Anonymous
83316
add a comment |
up vote
1
down vote
Depending on the compiler you use, you may need to explicitly state using preprocessor directives that you use 8080 commands. M80 uses .z80 and .8080 to instruct using respective instruction set mnemonics. See https://www.classic-computers.org.nz/system-80/software-manuals/manuals-Macro-80-Assembler.pdf page 20 (16 on the document's page).
If it will not compile in 8080 mode (due to Z80 directives in the source), then it means that sources are altered.The easiest way is to replace M with (HL), but I would not be surprised if resulting executable will not work properly at all.
answered 19 mins ago
Anonymous
83316
add a comment |
up vote
1
down vote
up vote
1
down vote
Depending on the compiler you use, you may need to explicitly state using preprocessor directives that you use 8080 commands. M80 uses .z80 and .8080 to instruct using respective instruction set mnemonics. See https://www.classic-computers.org.nz/system-80/software-manuals/manuals-Macro-80-Assembler.pdf page 20 (16 on the document's page).
If it will not compile in 8080 mode (due to Z80 directives in the source), then it means that sources are altered.The easiest way is to replace M with (HL), but I would not be surprised if resulting executable will not work properly at all.
answered 19 mins ago
Anonymous
83316
Depending on the compiler you use, you may need to explicitly state using preprocessor directives that you use 8080 commands. M80 uses .z80 and .8080 to instruct using respective instruction set mnemonics. See https://www.classic-computers.org.nz/system-80/software-manuals/manuals-Macro-80-Assembler.pdf page 20 (16 on the document's page).
If it will not compile in 8080 mode (due to Z80 directives in the source), then it means that sources are altered.The easiest way is to replace M with (HL), but I would not be surprised if resulting executable will not work properly at all.
answered 19 mins ago
Anonymous
83316
answered 19 mins ago
Anonymous
83316
answered 19 mins ago
Anonymous
83316
answered 19 mins ago
Anonymous
83316
83316
add a comment |
add a comment |
tergav17 is a new contributor. Be nice, and check out our Code of Conduct.
tergav17 is a new contributor. Be nice, and check out our Code of Conduct.
tergav17 is a new contributor. Be nice, and check out our Code of Conduct.
tergav17 is a new contributor. Be nice, and check out our Code of Conduct.
Thanks for contributing an answer to Retrocomputing Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Some of your past answers have not been well-received, and you're in danger of being blocked from answering.
Please pay close attention to the following guidance:
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fretrocomputing.stackexchange.com%2fquestions%2f8546%2fwhat-is-the-meaning-of-m-in-the-z80-statement-add-a-m%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
It might be helpful if you link the source in question and explain where you acquired it.
– Raffzahn
5 hours ago